9060 fuse replacement – Ransburg No. 2 Air Motor Atex Approved Unit 80086-XX User Manual

Page 43

AH----12

12----01.03 No. 2 Air Motor Handgun

01.03 No. 2 Air Motor Handgun

8. Place PTFE seal (Item 8), with shoulder fac-

8. Place PTFE seal (Item 8), with shoulder fac-
ing toward front end of drive shaft, onto the

ing toward front end of drive shaft, onto the

ing toward front end of drive shaft, onto the
drive shaft and slide it back until it contacts O

drive shaft and slide it back until it contacts O

drive shaft and slide it back until it contacts O----
ring (Item 9).

ring (Item 9).

9.Install O

9.Install O----ring (Item 4) on ceramic seal

ring (Item 4) on ceramic seal

(Item 5) and slide the ceramic seal onto

(Item 5) and slide the ceramic seal onto
drive shaft (Item 7) until it contacts PTFE

drive shaft (Item 7) until it contacts PTFE

drive shaft (Item 7) until it contacts PTFE
seal (Item 8).

seal (Item 8).

seal (Item 8).

10. Place the nut (Item 3) onto drive shaft

10. Place the nut (Item 3) onto drive shaft

10. Place the nut (Item 3) onto drive shaft
(Item 7) side with threads toward ceramic

(Item 7) side with threads toward ceramic

(Item 7) side with threads toward ceramic
seal (Item 5). Slide it back on drive shaft as

seal (Item 5). Slide it back on drive shaft as

seal (Item 5). Slide it back on drive shaft as
far as it will go.

far as it will go.

11. Slip the collar (Item 1) onto the drive

11. Slip the collar (Item 1) onto the drive
shaft (Item 7), align the two set screws with

shaft (Item 7), align the two set screws with

shaft (Item 7), align the two set screws with
the two flats in drive shaft. Secure the collar

the two flats in drive shaft. Secure the collar

the two flats in drive shaft. Secure the collar
to the drive shaft by tightening the two set

to the drive shaft by tightening the two set

to the drive shaft by tightening the two set
screws (Item 2).

screws (Item 2).

C A U T I O N

Clean the inner and outer faces of the

new seals and the front portion of the

new seals and the front portion of the
shaft carefully with solvent before re-

shaft carefully with solvent before re-

shaft carefully with solvent before re-
placing them. Oil or dirt deposit from

placing them. Oil or dirt deposit from

placing them. Oil or dirt deposit from
the hands could cause an improper

the hands could cause an improper

the hands could cause an improper
contact of seal faces. This is a DRY

contact of seal faces. This is a DRY

contact of seal faces. This is a DRY
seal and DOES NOT require grease or

seal and DOES NOT require grease or

seal and DOES NOT require grease or
oil.

oil.

C A U T I O N

DO NOT apply dielectric grease or

any other lubricant to the PTFE seal

any other lubricant to the PTFE seal
(Item 8), ceramic seal (Item 5), drive

(Item 8), ceramic seal (Item 5), drive

(Item 8), ceramic seal (Item 5), drive
shaft (Item 7), or collar (Item 1). The ap-

shaft (Item 7), or collar (Item 1). The ap-

shaft (Item 7), or collar (Item 1). The ap-
plication of dielectric grease or any oth-

plication of dielectric grease or any oth-

plication of dielectric grease or any oth-
er lubricant to these components can

er lubricant to these components can

er lubricant to these components can
cause premature failure of the motor.

cause premature failure of the motor.

12. Install the outer O

12. Install the outer O----ring (Item 6) on the

ring (Item 6) on the

drive shaft.

drive shaft.

13. Install the resistor (black ink end first) and

13. Install the resistor (black ink end first) and

13. Install the resistor (black ink end first) and
spring into the rear of the drive shaft (Item 7).

spring into the rear of the drive shaft (Item 7).

spring into the rear of the drive shaft (Item 7).
Spring must be long enough to contact end of

Spring must be long enough to contact end of

Spring must be long enough to contact end of
resistor and motor shaft.

resistor and motor shaft.

resistor and motor shaft.

14. Holding the gun assembly with the front of

14. Holding the gun assembly with the front of

14. Holding the gun assembly with the front of
the barrel angled slightly downward, slide the

the barrel angled slightly downward, slide the

the barrel angled slightly downward, slide the
drive shaft (Item 7) into the front of the barrel

drive shaft (Item 7) into the front of the barrel

drive shaft (Item 7) into the front of the barrel
until it bottoms. Rotate the drive shaft by hand

until it bottoms. Rotate the drive shaft by hand

until it bottoms. Rotate the drive shaft by hand
until you feel the slot engage the motor shaft

until you feel the slot engage the motor shaft

until you feel the slot engage the motor shaft
pin. Tighten nut (Item 3) to secure the drive

pin. Tighten nut (Item 3) to secure the drive

pin. Tighten nut (Item 3) to secure the drive
shaft to the gun assembly.

shaft to the gun assembly.

9060 Fuse Replacement

If the nut will not thread fully, the shaft is not

If the nut will not thread fully, the shaft is not
engaged. Unscrew and repeat Step 13.

engaged. Unscrew and repeat Step 13.

C A U T I O N

When ever the 9060 power supply is serviced,

When ever the 9060 power supply is serviced,
insure that the power is off to the unit.

insure that the power is off to the unit.

W A R N I N G

MAINTENANCE