Teledyne 6200A - Sulfides analyzer - Manual (Page 29)

TAI Model 6200A SO
2
Analyzer Operator Manual, 02164, Rev. G
6 OPTIONAL HARDWARE AND SOFTWARE............................................6-1
6.1 R
ACK
M
OUNT
O
PTIONS
.............................................................................................. 6-1
6.2 Z ERO /S PAN V ALVES ................................................................................................... 6-1
6.3 I
NTERNAL
Z
ERO
/S
PAN
(IZS) ....................................................................................... 6-3
6.4 A UTOCAL - S ETUP OF IZS AND Z ERO /S PAN V ALVES ..................................................... 6-3
6.5 P
ERMEATION
T
UBE
(
USED WITH
IZS
OPTION
) ............................................................... 6-6
6.6 4-20 M A, C URRENT L OOP O UTPUT ............................................................................. 6-9
6.7 S
TATUS
O
UTPUT
........................................................................................................ 6-9
6.8 RS-232 I NTERFACE ................................................................................................. 6-10
6.8.1 Setting Up the RS-232 Interface...................................................................... 6-10
6.8.2 Command Summary........................................................................................ 6-13
6.8.3 TEST Commands and Messages .................................................................... 6-17
6.8.4 WARNING Commands And Messages ........................................................... 6-18
6.8.5 CALIBRATION Commands and Messages ..................................................... 6-19
6.8.6 DIAGNOSTIC Commands and Messages....................................................... 6-20
6.8.7 DAS Commands and Reports ......................................................................... 6-21
6.8.8 VARIABLES Commands and Messages ......................................................... 6-24
7 CALIBRATION AND ZERO/SPAN CHECKS ...........................................7-1
7.1 M ANUAL Z ERO /S PAN C HECK OR C ALIBRATION THROUGH THE S AMPLE P ORT .................. 7-4
7.2 M
ANUAL
Z
ERO
/S
PAN
C
HECK OR
C
ALIBRATION WITH
Z
ERO
/S
PAN
V
ALVES
O
PTION
........... 7-6
7.3 M ANUAL Z ERO /S PAN C HECK WITH IZS O PTION ............................................................ 7-7
7.4 A
UTOMATIC
Z
ERO
/S
PAN
C
HECK
.................................................................................. 7-7
7.5 A UTOMATIC Z ERO /S PAN C ALIBRATION ......................................................................... 7-7
7.6 C
ALIBRATE ON
SO
2
P
ERMEATION
T
UBE
....................................................................... 7-8
7.7 U SE OF IZS OR Z ERO /S PAN V ALVES WITH R EMOTE C ONTACT C LOSURE ........................ 7-8
7.8 EPA P
ROTOCOL
C
ALIBRATION
.................................................................................... 7-9
7.8.1 Calibration of Equipment ................................................................................... 7-9
7.8.2 Calibration Gas Sources.................................................................................. 7-10
7.8.3 Data Recording Device.................................................................................... 7-12
7.8.4 Dynamic Multipoint Span Calibration ............................................................... 7-12
7.8.5 SO
2
Calibration Procedure............................................................................... 7-13
7.8.6 Calibration Frequency...................................................................................... 7-19
7.8.7 Other Quality Assurance Procedures .............................................................. 7-19
7.8.8 Summary of Quality Assurance Checks .......................................................... 7-21
7.8.9 ZERO and SPAN Checks ................................................................................ 7-22
7.8.10 Recommended Standards for Establishing Traceability ................................ 7-23
7.9 S PECIAL C ALIBRATION R EQUIREMENTS FOR D UAL R ANGE OR A UTO R ANGE .................. 7-24
7.10 C
ALIBRATION
Q
UALITY
............................................................................................ 7-25
7.11 R EFERENCES ......................................................................................................... 7-26
ii