Burkert Type 8056 User Manual
Page 61

- 61 -
RS232_485_ETP_MODBUS_BU_REV02.doc
Help command: GPEMT=?
MAX 31 CHR STRING if accepted
1:CMD ERR if GPRS not enabled
5:ACCESS ERR if insufficient access level
Read command: GPURL?
String value if command accepted
1:CMD ERR if GPRS not enabled
5:ACCESS ERR if insufficient access level
Set command:
GPURL=
string
0:OK if parameters accepted
1:CMD ERR if GPRS not enabled
2:PARAM ERR if
string
out of range
5:ACCESS ERR if insufficient access level
GPURL (GPrs URL) Reads or sets
the GPRS network URL used to fetch
the dynamic document in the http
server that performs the time
synchronization. The trailing “/”
preceding the URL and the eventual
“http://” must be omitted. The
maximum length is 31 characters.
Help command: GPURL=?
MAX 31 CHR STRING if accepted
1:CMD ERR if GPRS not enabled
5:ACCESS ERR if insufficient access level
Read command: GPASN?
String value if command accepted
1:CMD ERR if GPRS not enabled
5:ACCESS ERR if insufficient access level
Set command:
GPASN=
string
0:OK if parameters accepted
1:CMD ERR if GPRS not enabled
2:PARAM ERR if
string
out of range
5:ACCESS ERR if insufficient access level
GPASN (GPrs Authorized Sender
Number) Reads or sets the GPRS
network SMS authorized number
from which the device can accept
SMS commands. The value can
match exactly the sender number or
can be the first part only, leaving the
possibility to use adjacent valid
sender numbers. The maximum
length is 18 characters.
Help command: GPASN=?
MAX 18 CHR STRING if accepted
1:CMD ERR if GPRS not enabled
5:ACCESS ERR if insufficient access level
Read command: GPAUT?
value of auth. type if command accepted
1:CMD ERR if GPRS not enabled
5:ACCESS ERR if insufficient access level
Set command: GPAUT=
n
0:OK if parameters accepted
1:CMD ERR if GPRS not enabled
2:PARAM ERR if
n
out of range
5:ACCESS ERR if insufficient access level
GPAUT (GPrs Authentication Type)
Reads or sets the GPRS
authentication type used to access
the network. This parameter must be
set accordingly to what specifies the
wireless operator and it can be:
0=Normal (PAP), 1=Secure (CHAP),
2=None.
Help command: GPAUT=?
min <> max
if accepted
1:CMD ERR if GPRS not enabled
5:ACCESS ERR if insufficient access level
Read command: GPESE?
Status of email send functions if accepted
1:CMD ERR if RS232 port not enabled
5:ACCESS ERR if insufficient access level
Set command: GPESE=
n
0:OK if parameters accepted
1:CMD ERR if RS232 port not enabled
2:PARAM ERR if
n
out of rang
5:ACCESS ERR if insufficient access level
GPESE (GPrs Email Send Enable)
Enables or disables the sending of
the emails using the GPRS terminal.
Valid only if the RS232 port is
installed and enabled.
Valid only if the GPRS terminal is
installed and enabled.
Help command: GPESE=?
List of
num:description
if accepted
1:CMD ERR if RS232 port not enabled
5:ACCESS ERR if insufficient access level
Read command:
NOT
SUPPORTED
1:CMD ERR if read command is issued
Set command: GPDTS=1
0:OK if parameters accepted
1:CMD ERR if RS232 port not enabled
2:PARAM ERR if
n
not equal to 1
5:ACCESS ERR if insufficient access level
GPDTS (GPrs DaTa Send) Sends an
email containing data coming from
the enabled loggers using the GPRS
terminal.
Help command: GPDTS=?
1:EXECUTE
if accepted
1:CMD ERR if RS232 port not enabled
5:ACCESS ERR if insufficient access level
GPCFS (GPrs ConFiguration Send)
Sends an email containing all the
configuration data of the instrument
Read command:
NOT
SUPPORTED
1:CMD ERR if read command is issued
5:ACCESS ERR if insufficient access level