Veris Industries H8822 Install - Manual

VERIS INDUSTRIES
™
POWER MONITORING
INSTALLATION GUIDE
ZL0056-0C PAGE 1 ©2010 Veris Industries USA 800.354.8556 or +1.503.598.4564 / [email protected] 06101
Alta Labs, Enercept, Enspector, Hawkeye, Trustat, Veris, and the Veris ‘V’ logo are trademarks or registered trademarks of Veris Industries, L.L.C. in the USA and/or other countries.
H8822
Installer’s Specifications
Processors:
Main Processor ARM 9
I/O Co-Processor ARM 7
Operating System Linux
Flash ROM 16 MB NOR Flash (expandable with USB memory device)
Memory 32 MB RAM
LEDs 8x pulse input, 4 modem activity, Modbus TX/RX, power status
LCD 2 x 16 LCD Character, two buttons
LAN 10/100, Auto crossover detection
Modem:
Modem (phone) V.34 bis, 33,600 bps (Part number H8822)
Modem (cellular) GSM/GPRS Class 10, 85 kbps (Part number H8822GSM)
Protocols Modbus/RTU, Modbus/TCP, TCP/IP, PPP, HTTP/HTML, FTP, SNMP, SMTP, XML
Power Supply 24VDC, included
Serial Port RS-485 Modbus
Power Requirement 120-240VAC
Interval Recording User selectable 1-60 minutes. Default 15 minute interval
Inputs 8x, user selectable: 0-10V - Min/Max/Ave/Instantaneous;
4-20mA- Min/Max/Ave/Instantaneous; Pulse - Consumption, Rate;
Resistance - Min/Max/Ave/Instantaneous; Runtime - Runtime, Status
Approvals CE; FCC Part 15, Class A
USB Port USB memory expansion port
Outputs 2x, Dry contact 30VDC, 150mA max.
dimensions
AcquiSuite DR™ Data Acquisition System
HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH
• Follow safe electrical work practices. See NFPA 70E in the USA, or applicable local codes.
• This equipment must only be installed and serviced by qualified electrical personnel.
• Read, understand and follow the instructions before installing this product.
• Turn off all power supplying equipment before working on or inside the equipment.
• Use a properly rated voltage sensing device to confirm power is off.
DO NOT DEPEND ON THIS PRODUCT FOR VOLTAGE INDICATION
• Only install this product on insulated conductors.
Failure to follow these instructions will result in death or serious injury.
DANGER
quick install
1. Mount the AcquiSuite DR on the wall or other appropriate location.
2. Apply power.
3. Configure the IP address for the device.
4. Connect the device to a laptop or other computer.
5. Connect the AcquiSuite to a Modbus device (optional).
6. Configure the AcquiSuite to the local area netowrk (LAN).
H8822
Quick Install 1
Configuration 2
Overview 2
Wiring 2
Installation Checklist 3
Hardware Overview 3
Hardware Installation 4
Basic Network Configuration 5
AcquiSuite Administration Overview 7
Security 7
Modbus 8
Networking 12
System Options 16
Diagnostics 17
LCD Console 18
Log File Data 19
Retrieving Data from the AcquiSuite 22
table of contents
overview
The AcquiSuite DR™ data acquisition system is designed to allow owners and
managers of commercial and industrial facilities with a cost-effective means of
gathering crucial information in a timely manner. To meet these requirements, the
AcquiSuite DR™ system provides the installer with all the tools necessary to install
and configure the hardware and software with a minimum of time and investment.
8.2 in
(209 mm)
2.0 in
(51 mm)
9.3 in
(77 mm)