Roland SC-88 Pro - Manual (Page 90)

RT H Slow (RT High Frequency Slow Rate)
0.05 - 10.0 [10]
Adjust the speed of the high-range rotor for the low-
speed (Slow) setting.
RT H Fast (RT High Frequency Fast Rate)
0.05 - 10.0 [11]
Adjust the speed of the high-range rotor for the
high-speed (Fast) setting.
RT Hi Accl (RT High Frequency Acceleration)
0 - 15 [12]
Adjust the time over which the rotation speed of the
high-range rotor will change from low-speed to
high-speed (or high-speed to low-speed) rotation.
Smaller values will require greater time to reach the
new rotational speed.
RT Hi Lev (RT High Frequency Level)
0 - 127 [13]
Adjust the volume of the high-range rotor.
RT Sept (RT Separation) 0 - 127 [14]
Adjust the spatial spread of the rotary sound.
#RT Speed Slow/Fast [15]
Simultaneously switch the rotational speed of both
the low-range and the high-range rotors.
Slow : Slow down the rotation to the speci-
fied speeds (RT L Slow parameter /
RT H Slow parameter values).
Fast : Speed up the rotation to the specified
speeds (RT L Fast parameter / RT H
Fast parameter values).
RT Pan (RT Output Pan) L63 - 0 - R63 [18]
Adjust the stereo position of the rotary sound. L63
is far left, 0 is center, and R63 is far right.
RT Level 0 - 127 [19]
Adjust the volume of the rotary sound.
Level (Output level ) 0 - 127 [20]
Adjust the output level.
61: OD / Phaser(Overdrive/Distortion, Phaser)
[11H, 05H]
This connects an overdrive or distortion in parallel with
a phaser.
OD Sel (OD Select) Odrv/Dist [1]
Select either Overdrive or Distortion.
+OD Drive (OD Drive) 0 - 127 [2]
Adjust the depth of distortion. The volume will
change together with the depth of distortion.
OD Amp (OD Amp Simulator Type)
Smal/BltIn/ 2-Stk/3-Stk [3]
Select the type of guitar amp.
Small : small amp
BltIn : single-unit type amp
2-Stk : large double stack amp
3-Stk : large triple stack amp
OD Amp Sw (OD Amp Switch) Off/On [4]
Turn the OD Amp parameter on/off.
OD Pan (OD Output Pan) L63 - 0 - R63 [16]
Set the stereo location of the overdrive or distortion
sound. L63 is far left, 0 is center, and R63 is far
right.
OD Level 0 - 127 [17]
Adjust the overdrive or distortion volume.
PH Man (Phaser Manual) 100 - 8.0k [6]
Adjust the center frequency at which the sound will
be modulated.
#PH Rate (Phaser Rate) 0.05 - 10.0 [7]
Adjust the modulation speed.
PH Depth (Phaser Depth) 0 - 127 [8]
Adjust the modulation depth.
PH Reso (Phaser Resonance) 0 - 127 [9]
Adjust the emphasis for the region around the cen-
ter frequency specified by the PH Man parameter.
PH Mix (Phaser Mix Level) 0 - 127 [10]
Adjust the proportion of the phase-shifted sound
that will be mixed with the direct sound.
PH Pan (Phaser Output Pan) L63 - 0 - R63 [18]
Set the stereo location of the phaser sound. L63 is
far left, 0 is center, and R63 is far right.
PH Level 0 - 127 [19]
Adjust the volume of the phaser sound.
Level (Output level ) 0 - 127 [20]
Adjust the output level.
62: OD / AutoWah (Overdrive/Distortion, Auto-wah)
[11H, 06H]
This connects an Overdrive or Distortion in parallel
with an Auto-wah.
L
R Phaser
Overdrive/
Distortion
Pan
Pan
L
R Auto Wah
Overdrive/
Distortion
Pan
Pan
Chapter 4. Insertion Effects 88