Roland SC-88 Pro - Manual (Page 74)

Level (Output level ) 0 - 127 [20]
Adjust the output level.
36: OD
→
Flanger (Overdrive
→
Flanger)
[02H, 01H]
This effect connects an overdrive and a flanger in
series.
OD Drive (Overdrive drive ) 0 - 127 [1]
Adjust the degree of overdrive distortion. The vol-
ume will change together with the degree of distor-
tion.
+OD Pan (Overdrive output pan )
L63 - 0 - R63 [2]
Adjust the stereo location of the overdrive sound.
L6 is far left, 0 is center, and R63 is far right.
OD Amp (Overdrive Amp Simulator Type)
Small/BltIn/2-Stk/3-Stk [3]
Select the type of guitar amp.
Small : small amp
BltIn : single-unit type amp
2-Stk : large double stack amp
3-Stk : large triple stack amp
OD Amp Sw (Overdrive Amp Switch) Off/On [4]
Turn OD Amp on/off.
FL Dly (Flanger pre delay ) 0 - 100m [6]
Adjust the time delay from when the direct sound
begins until the flanger sound is heard.
FL Rate (Flanger rate ) 0.05 - 10.0 [7]
Adjust the modulation speed of the flanger effect.
FL Depth (Flanger depth ) 0 - 127 [8]
Adjust the modulation depth of the flanger effect.
FL Fb (Flanger feedback level ) -98% - +98% [9]
Adjust the proportion (%) of the flanger sound that
is fed back into the effect. Negative (-) settings will
invert the phase.
#FL Bal (Flanger balance) D> 0E - D 0
Adjust the volume balance between the sound
which passes through the flanger and the sound
which does not. With a setting of D>0E, only the
overdrive sound will be output, and with a setting of
D 0the flanger will be output. “
D
” and “
E
” respectively
indicate D (dry sound) and E (effect sound) values
of 100.
Low Gain -12 - +12 [17]
Adjust the low frequency gain.
Hi Gain (High gain ) -12 - +12 [18]
Adjust the high frequency gain.
Level (Output level ) 0 - 127 [20]
Adjust the output level.
37: OD
→
Delay (Overdrive
→
Delay) [02H, 02H]
This effect connects an overdrive and a delay in
series.
OD Drive (Overdrive drive ) 0 - 127 [1]
Adjust the degree of overdrive distortion. The vol-
ume will change together with the degree of distor-
tion.
+OD Pan (Overdrive output pan )
L63 - 0 - R63 [2]
Adjust the stereo location of the overdrive sound.
L63 is far left, 0 is center, and R63 is far right.
OD Amp (Overdrive Amp Simulator Type)
Small/BltIn/2-Stk/3-Stk [3]
Select the type of guitar amp.
Small : small amp
BltIn : single-unit type amp
2-Stk : large double stack amp
3-Stk : large triple stack amp
OD Amp Sw (Overdrive Amp Switch) Off/On [4]
Turn OD Amp on/off.
Dly Time (Delay time ) 0 - 500m [6]
Adjust the time delay from when the direct sound
begins until the delay sound is heard.
Dly Fb (Delay feedback level ) -98% - +98% [7]
Adjust the proportion (%) of the delay sound that is
fed back into the effect. Negative (-) settings will
invert the phase.
Dly HF (Delay HF damp ) 315 - 8k/Bypass [8]
Adjust the frequency above which delayed sound
fed back to the effect will be cut. If you do not wish
to cut the high frequencies of the feedback, set this
parameter to Bypass.
#Dly Bal (Delay balance ) D> 0E - D 0
Adjust the volume balance between the sound
which passes through the delay and the sound
which does not. With a setting of D>0E, only the
overdrive sound will be output, and with a setting of
D 0the delay will be output.
“
D
” or “
E
” on the display respectively means
D(direct sound) or E(effect sound) values of 100.
L
R
Flanger Overdrive
EQ
EQ
Balance L
R
Delay Overdrive
EQ
EQ
Balance
Chapter 4. Insertion Effects 72