Roland SC-88 Pro - Manual (Page 196)

Chapter 8. Appendix 194
● System Parameters [88]
Parameters affecting the entire unit, such as how the two MIDI IN connectors will function, are called System Parameters.
Address(H)
Size(H) Data(H) Parameter Description Default(H) Description
00 00 7F 00 00 01 00 - 01 SYSTEM MODE SET [88] 00 MODE1
00: MODE-1 (Single module mode)
01: MODE-2 (Double module mode)
(Rx. only)
* Refer to "System exclusive messages related to Mode settings" (page 191).
CHANNEL MSG RX PORT [88]
00 01 00 00 00 01 00 - 01 BLOCK00 PORT A - B 00 PORT A
: : : : :
00 01 0F 00 00 01 00 - 01 BLOCK0F PORT A - B 00 PORT A
00 01 10 00 00 01 00 - 01 BLOCK10 PORT A - B 01 PORT B
: : : : :
00 01 1F 00 00 01 00 - 01 BLOCK1F PORT A - B 01 PORT B
* You can modify the receiving MIDI port at which channel messages will be received for each BLOCK. We suggest that normally you use PORT A for BLOCK01-0F, and
PORT B for BLOCK10-1F. (In this case there is no need to change the setting.)
* Refer to page 196 for details of each BLOCK.
● Patch parameters
❍ Patch common parameters
In MODE-1 (Single module mode) this unit functions as a single sound source module with 32 Parts. In MODE-2 (Double module mode) it functions as two sound source mod-
ules with 16 Parts each. The parameters common to all Parts in each module are called Patch Common parameters.
Address(H) Size(H) Data(H) Parameter Description Default Value (H) Descrip-tion
40 00 00 00 00 04 0018 - 07E8 MASTER TUNE -100.0 - +100.0 [cent] 00 04 00 00 0 [cent]
40 00 01# Use nibblized data.
40 00 02#
40 00 03#
* Refer to section 5. Supplementary material, "About tuning" (page 208).
40 00 04 00 00 01 00 - 7F MASTER VOLUME 0 - 127 7F 127
(= F0 7F 7F 04 01 00 vv F7 )
40 00 05 00 00 01 28 - 58 MASTER KEY-SHIFT -24 - +24 [semitones] 40 0[semitones]
40 00 06 00 00 01 01 - 7F MASTER PAN -63 (LEFT) - +63 (RIGHT) 40 0 (CENTER)
40 00 7F 00 00 01 00 MODE SET 00 = GS Reset
(Rx. only)
* Refer to "System exclusive messages related to Mode settings" (page 191).
40 01 00 00 00 10 20 - 7F PATCH NAME 16 ASCII Characters
40 01 : #
40 01 0F#
40 01 30
00 00 01 00 - 07 REVERB MACRO 00: Room 1 04 Hall 2
01: Room 2
02: Room 3
03: Hall 1
04: Hall 2
05: Plate
06: Delay
07: Panning Delay
40 01 31 00 00 01 00 - 07 REVERB CHARACTER 0 - 7 04 4
40 01 32 00 00 01 00 - 07 REVERB PRE-LPF 0 - 7 00 0
40 01 33 00 00 01 00 - 7F REVERB LEVEL 0 - 127 40 64
40 01 34 00 00 01 00 - 7F REVERB TIME 0 - 127 40 64
40 01 35 00 00 01 00 - 7F REVERB DELAY FEEDBACK 0 - 127 00 0
40 01 37 00 00 01 00 - 7F REVERB PREDELAY TIME [88] 0 - 127[ms] 00 0
* REVERB MACRO is a macro parameter that allows global setting of reverb parameters. When you select the reverb type with REVERB MACRO, each reverb parameter will
be set to the most suitable value.
* REVERB CHARACTER is a parameter that changes the reverb algorithm. The value of REVERB CHARACTER corresponds to the REVERB MACRO of the same number.
* In MODE-2 (Double module mode), REVERB PREDELAY TIME cannot be used.