Roland SC-88 Pro User Manual
Page 76
#FL Bal (Flanger balance)
D> 0E - D 0 Adjust the volume balance between the sound “ D ” or “ E ” on the display respectively means D(direct sound) or E(effect sound) values of 100. Low Gain -12 - +12 [17] Adjust the low frequency gain. Hi Gain (High gain ) -12 - +12 [18] Adjust the high frequency gain. Level (Output level ) 0 - 127 [20] Adjust the output level. 40: DS → Delay (Distortion → Delay ) [02H, 05H] This effect connects a distortion and a delay in series. DS Drive (Distortion drive ) 0 - 127 [1] Adjust the degree of distortion. The volume will +DS Pan (Distortion output pan ) L63 - 0 - R63 [2] Adjust the stereo location of the distortion sound. DS Amp (Distortion Amp Simulator Type) Small/BltIn/2-Stk/3-Stk [3] Select the type of guitar amp. Small : small amp BltIn : single-unit type amp 2-Stk : large double stack amp 3-Stk : large triple stack amp DS Amp Sw (Distortion Amp Switch) Off/On [4] Turn DS Amp on/off. Dly Time (Delay time ) 0 - 500m [6] Adjust the time delay from when the direct sound Dly Fb (Delay feedback level ) -98% - +98% [7] Adjust the proportion (%) of the delay sound that is Dly HF (Delay HF damp ) 315 - 8k/Bypass [8] Adjust the frequency above which delayed sound #Dly Bal (Delay balance ) D> 0E - D 0 Adjust the volume balance between the sound D ” and “ E ” respectively indicate D (dry sound) and E (effect sound) values Low Gain -12 - +12 [17] Adjust the low frequency gain. Hi Gain (High gain ) -12 - +12 [18] Adjust the high frequency gain. Level (Output level ) 0 - 127 [20] Adjust the output level. 41: EH → Chorus (Enhancer → Chorus) [02H, 06H] This effect connects an enhancer and a chorus in +EH Sens (Enhancer Sensitivity ) 0 - 127 [1] Adjust the sensitivity of the enhancer. EH Mix (Enhancer Mix level ) 0 - 127 [2] Adjust the ratio with which the overtones generated Cho Dly (Chorus pre delay ) 0 - 100m [6] Adjust the time delay from when the direct sound Cho Rate (Chorus rate ) 0.05 - 10.0 [7] Adjust the modulation speed of the chorus effect. Cho Depth (Chorus depth ) 0 - 127 [8] Adjust the modulation depth of the chorus effect. #Cho Bal (Chorus balance ) D> 0E - D 0 Adjust the volume balance between the sound “ D ” or “ E ” on the display respectively means D(direct sound) or E(effect sound) values of 100. Low Gain -12 - +12 [17] Adjust the low frequency gain. L R Delay Distortion EQ EQ Balance Enhancer Enhancer Chorus L R EQ EQ Balance Chapter 4. Insertion Effects 74
which passes through the flanger and the sound
which does not. With a setting of D>0E, only the
distortion sound will be output, and with a setting of
D 0
change together with the degree of distortion.
L63 is far left, 0 is center, and R63 is far right.
begins until the delay sound is heard.
fed back into the effect. Negative (-) settings will
invert the phase.
fed back to the effect will be cut. If you do not wish
to cut the high frequencies of the feedback, set this
parameter to Bypass.
which passes through the delay and the sound
which does not. With a setting of D>0E, only the
distortion sound will be output, and with a setting of
D 0
of 100.
series.
by the enhancer are combined with the direct
sound.
begins until the chorus sound is heard.
which passes through the chorus and the sound
which does not. With a setting of D>0E, only the
enhancer sound will be output, and with a setting of
D 0