Roland SC-88 Pro User Manual
Page 78
Cho Rate (Chorus rate )
0.05 - 10.0 [2]
Adjust the modulation speed of the chorus effect.
Cho Depth (Chorus depth )
0 - 127 [3]
Adjust the modulation depth of the chorus effect.
+Cho Bal (Chorus balance )
D> 0E - D 0 Adjust the volume balance between the direct “ D ” or “ E ” on the display respectively means D(direct sound) or E(effect sound) values of 100. Dly Time (Delay time ) 0 - 500m [6] Adjust the time delay from when the direct sound Dly Fb (Delay feedback level ) -98% - +98% [7] Adjust the proportion (%) of the delay sound that is Dly HF (Delay HF damp ) 315 - 8k/Bypass [8] Adjust the frequency above which delayed sound #Dly Bal (Delay balance ) D> 0E - D 0 Adjust the volume balance between the sound “ D ” or “ E ” on the display respectively means D(direct sound) or E(effect sound) values of 100. Low Gain -12 - +12 [17] Adjust the low frequency gain. Hi Gain (High gain ) -12 - +12 [18] Adjust the high frequency gain. Level (Output level ) 0 - 127 [20] Adjust the output level. 45: FL → Delay (Flanger → Delay) [02H, 0AH] This effect connects a flanger and a delay in series. FL Dly (Flanger pre delay ) 0 - 100m [1] Adjust the time delay from when the direct sound FL Rate (Flanger rate ) 0.05 - 10.0 [2] Adjust the modulation speed of the flanger effect. FL Depth (Flanger depth ) 0 - 127 [3] Adjust the modulation depth of the flanger effect. +FL Fb (Flanger feedback level ) -98% - +98% [4] Adjust the proportion (%) of the flanger sound that FL Bal (Flanger balance ) D> 0E - D 0 Adjust the volume balance between the direct “ D ” or “ E ” on the display respectively means D(direct sound) or E(effect sound) values of 100. Dly Time (Delay time ) 0 - 500m [6] Adjust the time delay from when the direct sound Dly Fb (Delay feedback level ) -98% - +98% [7] Adjust the proportion (%) of the delay sound that is Dly HF (Delay HF damp ) 315 - 8k/Bypass [8] Adjust the frequency above which delayed sound #Dly Bal (Delay balance ) D> 0E - D 0 Adjust the volume balance between the sound “ D ” or “ E ” on the display respectively means D(direct sound) or E(effect sound) values of 100. Low Gain -12 - +12 [17] Adjust the low frequency gain. Hi Gain (High gain ) -12 - +12 [18] Adjust the high frequency gain. Level (Output level ) 0 - 127 [20] Adjust the output level. 46: Cho → Flanger (Chorus → Flanger) [02H, 0BH] This effect connects a chorus and a flanger in series. L R Delay EQ EQ Flanger L R Flanger EQ EQ Chorus Chapter 4. Insertion Effects 76
sound and the chorus sound. With a setting of “D>
0E,” only the direct sound will be output. With a set-
ting of “D 0
begins until the delay sound is heard.
fed back into the delay input. Negative (-) settings
will invert the phase.
fed back to the delay input will be cut. If you do not
wish to cut the high frequencies of the feedback, set
this parameter to Bypass.
which passes through the delay and the sound
which does not. With a setting of D>0E, only the
chorus sound will be output, and with a setting of D
0
begins until the flanger sound is heard.
is fed back into the effect. Negative (-) settings will
invert the phase.
sound and the flanger sound. With a setting of “D>
0E,” only the direct sound will be output. With a set-
ting of “D 0
begins until the delay sound is heard.
fed back into the delay input. Negative (-) settings
will invert the phase.
fed back to the delay input will be cut. If you do not
wish to cut the high frequencies of the delay feed-
back, set this parameter to Bypass.
which passes through the delay and the sound
which does not. With a setting of D>0E, only the
flanger sound will be output, and with a setting of D
0