KORG Pa300 Arranger - Manual (Page 317)

313 Effects
Modulation and Pitch Shift (Mod./P.Shift)
Appe
ndix
50: Detune
Using this effect, you can obtain a detune effect that offsets the
pitch of the effect sound slightly from the pitch of the input sig-
nal. Compared to the chorus effect, a more natural sound thick-
ness will be created.
d: Input Level Dmod [%]
d: Src
This parameter sets the dynamic modulation of the input level.
51: Pitch Shifter
This effect changes the pitch of the input signal. You can select
from three types: Fast (quick response), Medium, and Slow (pre-
serves tonal quality). You can also create an effect in which the
pitch is gradually raised (or dropped) using the delay with feed-
back.
a: Mode
This parameter switches the pitch shifter operating mode. With
Slow, tonal quality will not be changed too much. With Fast, the
effect becomes a Pitch Shifter that has a quick response, but may
change the tone. Medium is in-between these two. If you do not
need to set too much pitch shift amount, set this parameter to
Slow. If you wish to change the pitch significantly, use Fast.
b: Pitch Shift [1/2tone]
b: Src
b: Amt
c: Fine [cents]
c: Amt
The amount of pitch shift will use the value of the Pitch Shift
plus the Fine value. The amount of modulation will use the b:
Amt value plus the c: Amt.
The same Modulation Source is used for both Pitch Shift and
Fine .
e: Feedback Position
f: Feedback
When Feedback Position is set to Pre , the pitch shifter output is
again input to the pitch shifter. Therefore, if you specify a higher
a
Pitch Shift
[cents]
–100...+100
Sets the pitch difference from the
input signal
Src Off...Tempo
Selects a modulation source for
pitch shift
Amt –100...+100
Sets the modulation amount for
pitch shift
b
Delay Time
[msec]
0...1000 Sets the delay time
c
Feedback –100...+100 Sets the feedback amount
High Damp [%] 0...100
Sets the damping amount in the
high range
d
Input Level
Dmod [%]
–100...+100
Sets the modulation amount of the
input level
Src Off...Tempo
Selects the modulation source for
the input level
e
Wet/Dry
Dry, 1:99...99:1,
Wet Balance between the wet and dry
signal
Src Off...Tempo
Table , “Dynamic Modulation
sources,” on page 283
Amt –100...+100 Amount of modulation source
Left
Right
FX Amt
FX Amt
FX Amt = 100: Mono In - Mono Out / FX Amt = 0: Stereo In - Stereo Out
Input Level
Input Level
+
High Damp
Delay
Feedback
Detune
Input Level
L o u d
e r
Max Zero
Higher
D -mod
Input Level
Max Zero
Higher
D -mod
x1.0
x0.5 Input Level Dmod= +100
Input Level Dmod= +50
L o u d
e r
x1.0
x0.5
Input Level Dmod= –100
Input Level Dmod= –50
Input Level Dmod
a Mode
Slow, Medium,
Fast Switches Pitch Shifter mode
b
Pitch Shift [1/
2tone]
–24...+24
Sets the pitch shift amount by steps
of a semitone
Src Off...Tempo
Selects the modulation source of
pitch shift amount
Amt –24...+24
Sets the modulation amount of
pitch shift amount
c
Fine [cents] –100...+100
Sets the pitch shift amount by steps
of a cent
Amt –100...+100
Sets the modulation amount of
pitch shift amount
d
Delay Time
[msec]
0...2000 Sets the delay time
e
Feedback
Position
Pre, Post Switches the feedback connection
f
Feedback –100...+100
Sets the feedback amount
High Damp [%] 0...100
Sets the damping amount in the
high range
g
Input Level
Dmod [%]
–100...+100
Sets the modulation amount of the
input level
Src Off...Tempo
Selects the modulation source for
the input level
h
Wet/Dry
Dry, 1:99...99:1,
Wet Balance between the wet and dry
signal
Src Off...Tempo
Table , “Dynamic Modulation
sources,” on page 283
Amt –100...+100 Amount of modulation source
Left
Right
FX Amt
FX Amt
FX Amt = 100: Mono In - Mono Out / FX Amt = 0: Stereo In - Stereo Out
Input Level
Input Level
+
High Damp
Delay
Feedback
Pitch Shifter
Feedback Position
Pre Post