KORG Pa300 Arranger - Manual (Page 311)

307 Effects
Modulation and Pitch Shift (Mod./P.Shift)
Appe
ndix
41: 2Voice Resonator
This effect resonates the input signal at a specified pitch. You can
set the pitch, output level, and pan settings for two resonators
individually. You can control the resonance intensity via an LFO.
a: Control Mode
f: Voice 1: Resonance
h: Voice 2: Resonance
This parameter determines the resonance intensity.
When “Control Mode” = Manual, the “Resonance” parameter
sets the intensity of resonance. If the “Resonance” parameter has
a negative value, harmonics will be changed, and resonance will
occur at a pitch one octave lower.
When “Control Mode” = LFO, the intensity of resonance varies
according to the LFO. The LFO sways between positive and neg-
ative values, causing resonance to occur between specified
pitches an octave apart in turn.
When “Control Mode” = D-mod, the resonance is controlled by
the dynamic modulation source. If JS X or Ribbon is assigned as
the modulation source, the pitch an octave higher and lower can
be controlled, similar to when LFO is selected for Control Mode.
a: LFO/D-mod Invert
When “Control Mode” = LFO or D-mod, the controlled phase of
either Voice 1 or 2 will be reversed. When the resonance pitch is
set for Voice 1 (Resonance has a positive value), Voice 2 will res-
onate at a pitch an octave below (Resonance has a negative
value).
f: Voice 1: Pitch
f: Fine [cents]
h: Voice 2: Pitch
h: Fine [cents]
The Pitch parameter specifies the pitch of resonance by note
name. The “Fine” parameter allows for fine adjustment in steps
of cents.
g: High Damp [%]
i: High Damp [%]
This sets the amount of damping amount for the high frequen-
cies of the resonant sound. Lower values create a metallic sound
with a higher range of harmonics.
a
Control Mode
Manual, LFO,
D-mod Switches the controls of resonance
intensity
LFO/D-mod
Invert
Off, On
Reverses the Voice 1 and 2 control
when LFO/D-mod is selected
b
LFO Frequency
[Hz]
0.02...20.00 Sets the speed of the LFO
D-mod Src Off...Tempo
Selects the modulation source that
controls resonance intensity
c
MIDI Sync Off, On
When this is on, the LFO speed is set
by BPM, Base Note, and Times,
instead of Frequency
BPM
MIDI,
40.00...
300.00 MIDI syncs to the system tempo; 40–
300 sets the tempo manually for this
individual effect
Base Note r...w
Selects the type of notes that
specify the LFO speed
Times x1...x32
Sets the number of notes that
specify the LFO speed
d
Mod. Depth –100...+100
Sets the amount of resonance
intensity control via LFO/D-mod
Trim 0...100 Sets the input level at the resonator
e
Voice1: Pitch C0...B8 Sets the voice1 Pitch for resonance
Fine [cents] –50...+50
Fine-adjusts the voice 1 pitch for
resonance
Level 0...100 Sets the Voice1 output level
f
Voice1:
Resonance
–100...+100
Sets the intensity of resonance
when Control Mode = Manual
High Damp [%] 0...100
Sets the damping amount of
resonant sound in the high range
Pan
L6...L1, C,
R1...R6
Sets the Voice1 stereo image
g
Voice2: Pitch C0...B8 Sets the voice 2 Pitch for resonance
Fine [cents] –50...+50
Fine-adjusts the voice 2 pitch for
resonance
Level 0...100 Sets the Voice2 output level
h
Voice2:
Resonance
–100...+100
Sets the intensity of resonance
when Control Mode = Manual
High Damp [%] 0...100
Sets the damping amount of
resonant sound in the high range
Pan
L6...L1, C,
R1...R6
Sets the Voice2 stereo image
i
Wet/Dry
Dry, 1:99...99:1,
Wet Balance between the wet and dry
signal
Src Off...Tempo
Table , “Dynamic Modulation
sources,” on page 283
Amt –100...+100 Amount of modulation source
Left
Right
Resonance
FX Amt
FX Amt
FX Amt = 100: Mono In - Stereo Out / FX Amt = 0: Stereo In - Stereo Out
High Damp
High Damp
Trim
Trim
+
Level
Level Pan
Pan
Control Mode
D -mod
LFO
Manual
Invert: On/Off
Resonator
Resonator
Pitch, Fine [cents]