HEIDENHAIN iTNC 530 (340 49x-02) ISO programming - Manual (Page 620)

G functions
Tool movements
G00
G01
G02
G03
G05
G06
G07*
G10
G11
G12
G13
G15
G16
Straight-line interpolation, Cartesian coordinates,
rapid traverse
Straight-line interpolation, Cartesian coordinates
Circular interpolation, Cartesian coordinates,
clockwise
Circular interpolation, Cartesian coordinates,
counterclockwise
Circular interpolation, Cartesian coordinates,
without indication of direction
Circular interpolation, Cartesian coordinates,
tangential contour approach
Paraxial positioning block
Straight-line interpolation, polar coordinates, rapid
traverse
Straight-line interpolation, polar coordinates
Circular interpolation, polar coordinates, clockwise
Circular interpolation, polar coordinates,
counterclockwise
Circular interpolation, polar coordinates, without
indication of direction
Circular interpolation, polar coordinates, tangential
contour approach
Chamfer/Rounding/Approach contour/Depart contour
G24*
G25*
G26*
G27* Chamfer with length R
Corner rounding with radius R
Tangential contour approach with radius R
Tangential contour approach with radius R
Define the tool
G99* With tool number T, length L, radius R
Tool radius compensation
G40
G41
G42
G43
G44 No tool radius compensation
Tool radius compensation, left of the contour
Tool radius compensation, right of the contour
Paraxial compensation for G07, lengthening
Paraxial compensation for G07, shortening
Blank form definition for graphics
G30
G31 (G17/G18/G19) min. point
(G90/G91) max. point
Cycles for drilling, tapping and thread milling
G240
G200
G201
G202
G203
G204
G205
G206
G207
G208
G209 Centering
Drilling
Reaming
Boring
Universal drilling
Back boring
Universal pecking
Tapping with a floating tap holder
Rigid tapping
Bore milling
Tapping with chip breaking
Cycles for drilling, tapping and thread milling
G262
G263
G264
G265
G267 Thread milling
Thread milling/countersinking
Thread drilling/milling
Helical thread drilling/milling
External thread milling
Cycles for milling pockets, studs and slots
G210
G211
G212
G213
G214
G215
G251
G252
G253
G254 Slot milling with reciprocating plunge
Round slot with reciprocating plunge
Rectangular pocket finishing
Rectangular stud finishing
Circular pocket finishing
Circular stud finishing
Rectangular pocket
Circular pocket
Slot
Circular slot
Cycles for creating point patterns
G220
G221 Point pattern on circles
Linear point pattern
SL Cycles, group 2
G37
G120
G121
G122
G123
G124
G125
G127
G128
Contour geometry, list of subcontour program
numbers
Contour data (applies to G121 to G124)
Pilot drilling
Rough-out
Floor finishing
Side finishing
Contour train (machining open contour)
Cylinder surface
Cylindrical surface slot
Coordinate transformations
G53
G54
G28
G73
G72
G80
G247 Datum shift in datum table
Datum shift in program
Mirror image
Rotation of the coordinate system
Scaling factor (reduce or enlarge contour)
Tilting the Working Plane
Datum setting
Cycles for multipass milling
G60
G230
G231 Run 3-D data
Multipass milling of plane surfaces
Multipass milling of tilted surfaces
*) Non-modal function
Touch probe cycles for measuring workpiece
misalignment
G400
G401
G402
G403
G404
G405 Basic rotation from two points
Basic rotation from two holes
Basic rotation from two studs
Compensate a basic rotation via a rotary axis
Set basic rotation
Compensating misalignment with the C axis
G functions