HEIDENHAIN ND 1200T User Manual
Nd 1200 t tool-chek
Table of contents
Document Outline
- Contents
- About this manual
- Who should read
- this guide i
- What this guide
- covers
- Conventions and
- Basic terms
- Measurement
- polarity
- Measurement
- resolution in
- the guide
- Icons
- Type styles
- Accuracy and
- precision
- System configuration
- and setup
- Overview
- Specifications
- Input voltage range:
- Fuse:
- Input Frequency:
- Environmental Conditions:
- Dimensions:
- LCD:
- Resolution:
- ENC tests:
- Getting ready to operate the TC200
- Location and mounting 2-2
- Power cord and plug 2-2
- Power surge suppressor 2-2
- Liquids 2-2
- Configuration and system setup 2-2
- Checking connections 2-2
- Applying power 2-3
- Initial system settings
- Adjusting LCD tilt 2-4
- Adjusting LCD brightness 2-4
- Setting measurement and display parameters 2-4
- Diameter/Radius 2-4
- Absolute/Incremental 2-4
- Unit of measure (Linear)
- Help 2-5
- Feature selection keys 2-6
- Setting gage 2-6
- Tool 2-6
- Tool Sequence 2-6
- Circle
- Angle 2-7
- Basic operating 2-8
- procedures 2-8
- To measure and store a setting gage 2-8
- To measure and store a tool 2-12
- Creating a tool sequence 2-14
- Running a tool sequence 2-16
- Measuring a circle 2-19
- To measure a circle 2-19
- Measuring an angle 2-22
- To measure an angle 2-22
- Zeroing Axes 2-25
- Freezing Axes 2-25
- Setup
- Configuring the TC200
- Basic setup terms
- Accessing the
- Setup menu
- Using the 3-3
- Setup menu 3-3
- Setup Instructions
- Command Keys
- Enter Key 3-4
- Finish Key 3-4
- Cancel Key
- Quit Key
- Supervisor Password
- To enter the password
- About 3-6
- Display
- MM Disp Res 3-8
- Inch Disp Res 3-8
- DMS Disp Res 3-9
- DD Disp Res 3-10
- Startup Linear 3-10
- Startup Angular 3-11
- Radix 3-11
- Current Angular
- Encoders
- Axis 3-13
- Resolution (Res)
- Type 3-14
- Reference Marks 3-14
- MZ Cnts 3-15
- Reversed 3-15
- Interpolation 3-16
- Units 3-16
- Print 3-17
- Auto Label 3-17
- Auto Report 3-18
- Label Format 3-18
- Pre Line 3-19
- Post Line 3-19
- Pre Form 3-19
- Post Form 3-20
- Print Report 3-20
- Label Lines 3-20
- Skip Lines 3-21
- Label Indent
- Ports 3-23
- Baud 3-24
- Word Len (word length) 3-24
- Stop Bits 3-24
- Parity 3-25
- Handshake 3-25
- Data/ Parallel Data 3-26
- EOC Delay (end of character delay) 3-26
- EOL Delay (end of line delay)
- Squareness 3-28
- Angle 3-28
- Master Axis
- Error Correction
- Linear Error
- Correction (LEC)
- Segmented Linear
- Error Correction
- (SLEC)
- Misc. (miscellaneous)
- Key Delay 3-35
- Volume
- Libraries
- Use Locations
- Tool Button
- SG 00 master
- SG Edit Lock 3-37
- SG Cal Lock 3-38
- Tool Sequence Edit Lock 3-38
- Clock 3-39
- Year
- Month 3-40
- Day
- Hours 3-40
- Minutes 3-41
- Seconds 3-41
- Date Format 3-41
- Time Format 3-42
- Communications
- RS232 port 4-1
- Default settings
- Ports section of Setup menu: 4-2
- Print section of Setup menu: 4-2
- Feature print formats
- Feature Formats 4-4
- Print Setup 4-4
- Pre Line 4-5
- Post Line 4-5
- Pre Form 4-5
- Post Form 4-5
- Print Report 4-5
- Print Labels 4-6
- Print POT 4-6
- Num Label Lines 4-6
- Num Skip Lines 4-6
- Amt Label Indent 4-6
- Glossary
- A
- B
- C
- D
- E
- F
- H
- I
- K
- L
- M
- N
- O
- P
- Q
- R
- S
- T
- U
- V
- W
- Y
- Z