Rockwell Automation SP600 User Manual Version 3.0 - Manual (Page 8)

VI SP600 AC Drive User Manual
Figure 11.1 – Motor Overload Hertz........................................................ 11-11
Figure 11.2 – Custom V/Hz Curve .......................................................... 11-12
Figure 11.3 – Fan/Pump Curve............................................................... 11-13
Figure 11.4 – Speed Limits ..................................................................... 11-13
Figure 11.5 – Compensation (56) ........................................................... 11-14
Figure 11.6 – Speed Control Method ...................................................... 11-19
Figure 11.7 – Speed Limits ..................................................................... 11-20
Figure 11.8 – Trim Input Select............................................................... 11-26
Figure 11.9 – Trim Out Select (118)........................................................ 11-27
Figure 11.10 – PI Configuration (124)..................................................... 11-29
Figure 11.11 – PI Control (125)............................................................... 11-31
Figure 11.12 – PI Preload Value ............................................................. 11-34
Figure 11.13 – PI Status (134) ................................................................ 11-35
Figure 11.14 – Save OIM Ref (192) ........................................................ 11-51
Figure 11.15 – Save MOP Ref (194)....................................................... 11-52
Figure 11.16 – Dyn UserSet Cnfg ........................................................... 11-56
Figure 11.17 – DynUsrSetSel ................................................................. 11-57
Figure 11.18 – Drive Status 1 (209) ........................................................ 11-58
Figure 11.19 – Drive Status 2 (210) ........................................................ 11-59
Figure 11.20 – Drive Alarm 1 (211)......................................................... 11-60
Figure 11.21 – Drive Alarm 2 (212)......................................................... 11-60
Figure 11.22 – Start Inhibits (214)........................................................... 11-61
Figure 11.23 – Dig In Status (216) .......................................................... 11-62
Figure 11.24 – Dig Out Status (217) ....................................................... 11-63
Figure 11.25 – Status 1 @ Fault (227).................................................... 11-65
Figure 11.26 – Status 2 @ Fault (228).................................................... 11-65
Figure 11.27 – Alarm 1 @ Fault (229) .................................................... 11-66
Figure 11.28 – Alarm 2 @ Fault (230) .................................................... 11-66
Figure 11.29 – Fault Config 1 (238) ........................................................ 11-68
Figure 11.30 – Alarm Config 1 (259)....................................................... 11-69
Figure 11.31 – Drive Logic Rslt (271) ..................................................... 11-70
Figure 11.32 – Manual Mask (286) ......................................................... 11-71
Figure 11.33 – Stop Owner ..................................................................... 11-72
Figure 11.34 – Manual Owner................................................................. 11-72
Figure 11.35 – Anlg In Config (320) ........................................................ 11-76
Figure 11.36 – Anlg In Sqr Root (321) .................................................... 11-76
Figure 11.37 – Analog Out Config........................................................... 11-80
Figure 11.38 – Anlg Out Absolute (341).................................................. 11-80
Figure 12.1 – Location of DC Bus Voltage Measuring Points ................... 12-2
Figure 12.2 – Location of Precharge Status LED...................................... 12-3
Figure 12.3 – Location of the Ready LED ................................................. 12-4
Figure 12.4 – Sample Fault Screen on the LCD OIM ............................. 12-10
Figure 12.5 – Accessing the Fault Queue............................................... 12-24
Figure 12.6 – Sample Fault Queue Entry................................................ 12-24
Figure 12.7 – Accessing the Fault Parameters ....................................... 12-25
Figure 12.8 – Accessing the Drive Status Parameters ........................... 12-25
Figure 12.9 – Accessing the Device Version Information ....................... 12-26