Enerpac ST-202 - Manual (Page 16)

16
10.0 SPÉCIFICATIONS POUR L’USINAGE
DES BRAS DE BRIDAGE
Voir Pression et débit, page 14 pour la mesure
correcte de la longueur du bras. Pour déterminer la
force de bridage maximum du bras, voir les
diagrammes de force de bridage/longueur de bras,
page 11.
Les dimensions sont en mm (po).
9,0 kN (2024 lb) 18,8 kN (3900 lb) 35,0 kN (7600 lb)
"A" 25 (0.99) 30 (1.18) 40(1.58)
"B" Max. 200 (7.88) 215 (8.47) 224 (8.83)
"C" 40 (1.58) 60 (2.36) 70 (2.76)
"D" 16 (0.63) 21 (0.83) 34 (1.34)
"E" 22 (0.87) 25 (0.99) 30 (1.18)
"F"(3 emplacements) 86 (3.38) 107 (4.22) 114 (4.49)
"G" 30 (1.18) 35 (1.38) 40 (1.58)
"H" 12,5 (0.49) 15 (0.59) 20 (0.79)
"J" 20 (0.79) 30 (1.18) 35 (1.38)
"K" (diám.) Ш 14 (0.55) Ш 17 (0.67) Ш 17 (0.67)
"L" 9 (0.35) 11 (0.43) 11 (0.43)
"M" (diám.) Ш 9 (0.35) Ш 11 (0.43) Ш 11 (0.43)
"N" (traversant) M10 x 1.25 M12 x 1.25 M16 x 1.50
"P" 9 (0.35) 12,8 (0.50) 15 (0.59)
"Q" 18 (0.71) 25,5 (1.00) 30 (1.18 )
"R" 11°-12° 9°-10° 16°-17°
"S" (diám.) Ш 27,85-27,95 Ш 35,50-35,60 Ш 41,50-41,60
(1.097-1.101) (1.399-1.402) (1.635-1.638)
"T" (diám.) Ø 25 H8 Ø 32 H8 Ø 38 H8
(0.9848-0.9858) (1.2604-1.2614) (1.4965-1.4975)
"U" 3,9-4,2 (0.15-0.17) 5,1-5,5 (0.20-0.22) 4,9-5,3 (0.19-0.21)
"V" 2,8-3,3 (0.11-0.13) 2,8-3,3 (0.11-0.13) 2,8-3,3 (0.11-0.13)
55˚-60˚
"U"
"T" "S"
0,08 [.003]
A
A
63P [1,6]
1,1-1,5 [.04-.06]
2,1-3,0 [.08-.12]
"J"
"L"
"P"
"M" "K" "N"
"D"
"H"
"A"
"G"
"E"
"B"
"Q"
40˚-50˚
"V"
"C"
“F”
3-emplacements
“R”
2
-emplacements