HP ProLiant SL2500 Scalable System User Manual

Hp advanced power manager user guide

This manual is related to the following products:

ProLiant SL6500 Scalable System ProLiant SL4500 Scalable System Apollo 6000 Chassis

Table of contents

Document Outline

HP Advanced Power Manager User Guide
Abstract
Notice
Contents
Introduction
- HP APM overview
Installation and configuration
- Prerequisites for installation
- Preparing for installation
- Configuring the HP APM for the first time
- Configuring the HP APM
  - Serial port configuration
  - Network configuration
- Duplicating the configuration
Command Line Interface
- Command line conventions
- Accessing the HP APM command line interface
- Saving configurations
- Topology and inventory
Logging
- Overview of logging
- Internal logging
  - Showing and clearing the event log
  - Showing and clearing the fault log
- External logging
- HP APM fault messages
- XML-related fault messages
- Working with RADIUS servers
Power capping
- Power capping overview
- Power capping requirements
- Power capping and measurement tolerance
- Invalidating a power baseline
- Power capping licensing
- HP APM and HP APM Distribution Module cabling
- Rack level power capping
  - Power baseline
  - Setting power capping
- Power commands
General commands
- Working with passwords
  - Setting HP APM passwords
  - Disabling HP APM passwords
  - Changing HP APM passwords
  - Resetting factory settings for HP APM
- Working with accounts
  - Adding an account
  - Removing an account
  - Showing accounts
- Working with zones
  - Adding zones
  - Removing zones
  - Showing zones
  - Saving zones
- Using password recovery
- Showing configurations
- Using the help
- Setting the name
- Setting the time
- Setting the session timeout
- Setting the UID LED
- Showing information
- Showing the name
- Showing the time
- Showing the version
- Rebooting and resetting factory settings
- Rebooting the HP Moonshot 1500 Chassis CM module
- Performing a reset
- Performing a reset buddy
- Clearing the screen
- Resetting factory settings
- Exiting, logging out, or quitting HP APM
- Connecting and setting ports
Using SNMP
- SNMP overview
- Enabling SNMP
- Displaying SNMP parameters
- Setting the SNMP read-only community string
- Setting the SNMP read-write community string
- Setting the SNMP contact
- Setting the SNMP location
- Setting SNMP trap destinations
- SNMP support of cpqHoSwRunningTable
Using XML
- XML overview
- Enabling XML
- Showing and resetting keys
- Logging in through XML
- Modifying the user account
- Requesting information with XML commands
- Modifying compute node power
- Requesting compute power node status
- Resetting HP APM
Firmware
- Upgrading the firmware
Troubleshooting
- Alert messages
- Devices not discovered
CLI commands
- Clear faults
- Clear log
- Clear screen
- Disable Ethernet
- Enable Ethernet
- Disable telnet
- Enable telnet
- Disable SSH
- Enable SSH
- Remove account
- Add account
- Disable password
- Enable password
- Set password account
- Ping
- Exit
- Help
- Logout
- Quit
- Reset
- Reset buddy
- Reboot
- Reboot CM
- Reset factory
- Save
- Save config
- Set IP
- Set gateway
- Set name
- Set power
- Set serial
- Set syslog
- Set time
- Set timeout
- Set power baseline
- Set power cap
- Set asset info
- Show accounts
- Show config
- Show faults
- Show info
- Show log
- Show syslog
- Show servers
- Show topology
- Show asset info
- Show MAC address
- Show time
- Show power baseline
- Show version
- Upgrade image
- Add zone
- Save zones
- Show zones
- Remove zone
- Enable pollpower
- Disable pollpower
- Enable SNMP
- Disable SNMP
- Show SNMP
- Set SNMP RO
- Set SNMP RW
- Set SNMP contact
- Set SNMP location
- Set SNMP trapdest
- Enable XML
- Enable XML secure
- Disable XML
- Show keys
- Reset keys
- Add RADIUS server
- Enable RADIUS
- Disable RADIUS
- Remove RADIUS server
- Show RADIUS
- Set RADIUS pollnum
- Set RADIUS pollsec
- Enable NTP
- Set NTP server
- Set NTP poll
- Show NTP server
- Show NTP poll
- Disable NTP
- Connect port
- Set port
XML commands
- Login
- Modify user
- Get firmware version
- Get rack topology
- Get rack information
- Modify compute node power
- Modify all compute node power
- Get compute node
- Get all compute node power
- Reset HP APM
Supported MIB objects
- Supported cpqRack MIB objects
- Supported cpqHostOs MIB objects
- Supported rfc1213 MIB objects
- PDU identity table
- PDU input table
Regulatory information
- Safety and regulatory compliance
- Belarus Kazakhstan Russia marking
- Turkey RoHS material content declaration
- Ukraine RoHS material content declaration
- Warranty information
Support and other resources
- Before you contact HP
- HP contact information
Acronyms and abbreviations
Documentation feedback
Index