HP ProLiant SL2500 Scalable System User Manual

Hp advanced power manager user guide

Text mode
Original mode

HP Advanced Power Manager

User Guide

Abstract

This guide provides installation and operation guidance for the HP Advanced Power Manager. This guide is for the person who installs, administers,

and troubleshoots servers and storage systems.

Part Number: 747697-001
June 2014

Edition: 1

This manual is related to the following products:

ProLiant SL6500 Scalable System ProLiant SL4500 Scalable System Apollo 6000 Chassis

Table of contents

Document Outline

HP Advanced Power Manager User Guide
Abstract
Notice
Contents
Introduction
- HP APM overview
Installation and configuration
- Prerequisites for installation
- Preparing for installation
- Configuring the HP APM for the first time
- Configuring the HP APM
  - Serial port configuration
  - Network configuration
- Duplicating the configuration
Command Line Interface
- Command line conventions
- Accessing the HP APM command line interface
- Saving configurations
- Topology and inventory
Logging
- Overview of logging
- Internal logging
  - Showing and clearing the event log
  - Showing and clearing the fault log
- External logging
- HP APM fault messages
- XML-related fault messages
- Working with RADIUS servers
Power capping
- Power capping overview
- Power capping requirements
- Power capping and measurement tolerance
- Invalidating a power baseline
- Power capping licensing
- HP APM and HP APM Distribution Module cabling
- Rack level power capping
  - Power baseline
  - Setting power capping
- Power commands
General commands
- Working with passwords
  - Setting HP APM passwords
  - Disabling HP APM passwords
  - Changing HP APM passwords
  - Resetting factory settings for HP APM
- Working with accounts
  - Adding an account
  - Removing an account
  - Showing accounts
- Working with zones
  - Adding zones
  - Removing zones
  - Showing zones
  - Saving zones
- Using password recovery
- Showing configurations
- Using the help
- Setting the name
- Setting the time
- Setting the session timeout
- Setting the UID LED
- Showing information
- Showing the name
- Showing the time
- Showing the version
- Rebooting and resetting factory settings
- Rebooting the HP Moonshot 1500 Chassis CM module
- Performing a reset
- Performing a reset buddy
- Clearing the screen
- Resetting factory settings
- Exiting, logging out, or quitting HP APM
- Connecting and setting ports
Using SNMP
- SNMP overview
- Enabling SNMP
- Displaying SNMP parameters
- Setting the SNMP read-only community string
- Setting the SNMP read-write community string
- Setting the SNMP contact
- Setting the SNMP location
- Setting SNMP trap destinations
- SNMP support of cpqHoSwRunningTable
Using XML
- XML overview
- Enabling XML
- Showing and resetting keys
- Logging in through XML
- Modifying the user account
- Requesting information with XML commands
- Modifying compute node power
- Requesting compute power node status
- Resetting HP APM
Firmware
- Upgrading the firmware
Troubleshooting
- Alert messages
- Devices not discovered
CLI commands
- Clear faults
- Clear log
- Clear screen
- Disable Ethernet
- Enable Ethernet
- Disable telnet
- Enable telnet
- Disable SSH
- Enable SSH
- Remove account
- Add account
- Disable password
- Enable password
- Set password account
- Ping
- Exit
- Help
- Logout
- Quit
- Reset
- Reset buddy
- Reboot
- Reboot CM
- Reset factory
- Save
- Save config
- Set IP
- Set gateway
- Set name
- Set power
- Set serial
- Set syslog
- Set time
- Set timeout
- Set power baseline
- Set power cap
- Set asset info
- Show accounts
- Show config
- Show faults
- Show info
- Show log
- Show syslog
- Show servers
- Show topology
- Show asset info
- Show MAC address
- Show time
- Show power baseline
- Show version
- Upgrade image
- Add zone
- Save zones
- Show zones
- Remove zone
- Enable pollpower
- Disable pollpower
- Enable SNMP
- Disable SNMP
- Show SNMP
- Set SNMP RO
- Set SNMP RW
- Set SNMP contact
- Set SNMP location
- Set SNMP trapdest
- Enable XML
- Enable XML secure
- Disable XML
- Show keys
- Reset keys
- Add RADIUS server
- Enable RADIUS
- Disable RADIUS
- Remove RADIUS server
- Show RADIUS
- Set RADIUS pollnum
- Set RADIUS pollsec
- Enable NTP
- Set NTP server
- Set NTP poll
- Show NTP server
- Show NTP poll
- Disable NTP
- Connect port
- Set port
XML commands
- Login
- Modify user
- Get firmware version
- Get rack topology
- Get rack information
- Modify compute node power
- Modify all compute node power
- Get compute node
- Get all compute node power
- Reset HP APM
Supported MIB objects
- Supported cpqRack MIB objects
- Supported cpqHostOs MIB objects
- Supported rfc1213 MIB objects
- PDU identity table
- PDU input table
Regulatory information
- Safety and regulatory compliance
- Belarus Kazakhstan Russia marking
- Turkey RoHS material content declaration
- Ukraine RoHS material content declaration
- Warranty information
Support and other resources
- Before you contact HP
- HP contact information
Acronyms and abbreviations
Documentation feedback
Index