KROHNE GFC 300 FOUNDATION FIELDBUS - Manual (Page 57)

OPERATION
4
57
GFC 300
www.krohne.com 07/2012 - 4001866001 - AD GFC 300 FF R01 en
Update State R A discrete enumeration which gives an indication of whether
the alert has been reported.
Uninitialized
Setting:
Uninitialized / Update reported / Update not reported
Time Stamp R The time when evaluation of the block was started and a
change in alarm/event state was detected that is unreported.
The time stamp value will be maintained constant until alert
confirmation has been received - even if another change of
state occurs. Time stamp records the time when parameter
was updated.
Uninitialized
Setting:
MM / DD / YY (Month / Day / Year)
HH:MM:SS (Hour:Minute:Second)
Static Revision R The static revision of the block whose static parameter was
changed and is being reported. It is possible for the present
value of static revision to be greater than this because static
can be changed at any time.
0
Setting:
0…65535
Relative Index R The OD index of the static parameter whose change caused
this alert, minus the FB starting index. If the update event was
caused by a write to multiple parameters at the same time,
then this attribute will be zero.
0
Setting:
0…65535
ARITH_TYPE ARITH_TYPE ARITH_TYPE ARITH_TYPE
Arithmetic Type Arithmetic Type Arithmetic Type Arithmetic Type
R/W Uninitialized
Setting:
Uninitialized / Flow compensation (linear) / Flow
compensation (square root) / Flow compensation
(approximate) / BTU flow / Traditional Multiply/Divide /
Average / Traditional Summer / Fourth Order Polynomial /
Simple HTG compensated level
BAL_TIME BAL_TIME BAL_TIME BAL_TIME
Balance Time Balance Time Balance Time Balance Time
R/W This specifies the time for the internal working value of bias or
ratio to return to the operator set bias or ratio, in seconds. In
the PID block, it may be used to specify the time constant at
which the integral term will move to obtain balance when the
output is limited and the mode is Auto, Cas, or RCas.
0
BIAS BIAS BIAS BIAS
Bias Bias Bias Bias
R/W The bias value used in computing the function block output,
expressed in engineering units.
0
BIAS_IN_1 BIAS_IN_1 BIAS_IN_1 BIAS_IN_1
Bias Input 1 Bias Input 1 Bias Input 1 Bias Input 1
R/W The constant to be added to IN_1. 0
BIAS_IN_2 BIAS_IN_2 BIAS_IN_2 BIAS_IN_2
Bias Input 2 Bias Input 2 Bias Input 2 Bias Input 2
R/W The constant to be added to IN_2. 0
BIAS_IN_3 BIAS_IN_3 BIAS_IN_3 BIAS_IN_3
Bias Input 3 Bias Input 3 Bias Input 3 Bias Input 3
R/W The constant to be added to IN_3. 0
COMP_HI_LIM COMP_HI_LIM COMP_HI_LIM COMP_HI_LIM
Compensation Compensation Compensation Compensation
High Limit High Limit High Limit High Limit
R/W The high limit imposed on the PV compensation term. 0
COMP_LO_LIM COMP_LO_LIM COMP_LO_LIM COMP_LO_LIM
Compensation Low Compensation Low Compensation Low Compensation Low
Limit Limit Limit Limit
R/W The low limit imposed on the PV compensation term. 0
GAIN GAIN GAIN GAIN
Gain Gain Gain Gain
R/W Dimensionless value used by the block algorithm in
calculating the block output.
0
GAIN_IN_1 GAIN_IN_1 GAIN_IN_1 GAIN_IN_1
Gain Input 1 Gain Input 1 Gain Input 1 Gain Input 1
R/W The constant to be multiplied times (IN_1 + bias). 0
Parameter Parameter Parameter Parameter
DD name Access Description and settings Initial Value