Operation – KROHNE GFC 300 FOUNDATION FIELDBUS User Manual
Page 17
OPERATION
4
17
GFC 300
www.krohne.com
07/2012 - 4001866001 - AD GFC 300 FF R01 en
FRAM_DIAG
FRAM Diagnosis
R
Result of FRAM self diagnosis.
ok
Setting:
ok / not supported action / unknown / busy / wait / first init /
changed / bit09 / parameter error / page error / chip error /
write error / warning: inconsistent / warning: uncertain /
warning: write cycles / warning: one header / ok, page high
workLOAD
R
Work load of the processor.
Current work load
DIAGNOSIS_BLK
DIAGNOSIS_BLK
DIAGNOSIS_BLK
DIAGNOSIS_BLK
Diagnosis Block
Diagnosis Block
Diagnosis Block
Diagnosis Block
R
Detailed diagnosis of the blocks.
-
RB_DIAG
RB Diagnosis
R
Reason for bits set at BLK_ERR and other diagnosis.
Current diagnosis
Setting:
Startup Device / RB: MODE_BLK.ACTUAL is OOS / Memory
failure / Operating System / new: ID, DEV_TYPE, SNR / no GDC
Communication / Startup GDC, data invalid / Startup Sensor,
data valid / C-Number doesn't match to FF Software /
Hardware changed, C raw != C detected / Data Base doesn't
match to FF Software / MODE_BLK.PERMITTED doesn't
include Auto / MODE_BLK.TARGET is set OOS / GDC bold F
message / GDC F message / write from GDC to RB/TB doesn't
work / GDC Mfr unknown / GDC serial number / Boardinfo
incomplete or corrupt / action: write from GDC to RB/TB /
GDC W: no, M: no / GDC W: no, M: some /
GDC W: some, M: no / GDC W: no, M: all /
GDC W: all, M: no / GDC W: some, M: some /
GDC W: some, M: all / GDC W: all, M: some /
GDC Communication few loss / RS_STATE is not On-Line /
simulation active / unknown reason / Ok
TB1_DIAG
TB1 Diagnosis
R
Reason for bits set at BLK_ERR and other diagnosis.
Current diagnosis
Startup Device / RB: MODE_BLK.ACTUAL is OOS / Memory
failure / no GDC Communication / Startup GDC, data invalid /
Startup Sensor, data valid / Data Base doesn't match to FF
Software / MODE_BLK.PERMITTED doesn't include Auto /
MODE_BLK.TARGET is set OOS / GDC bold F message / GDC F
message / write from GDC to RB/TB doesn't work / Sensor
serial number / Sensor calibration date / GDC unit not
convertible to TB.prim_val / prim_val is outside range /
action: write from GDC to RB/TB / GDC Communication few
loss / no unit of GDC / GDC unit can't be converted to
TB.prim_range / a GDC value was not received / a GDC short
status is fatal or warn2 / PRIMARY_VALUE_1.status is
Uncertain / unknown reason / Ok
TB2_DIAG
TB 2
R
Reason for bits set at BLK_ERR and other diagnosis.
Current diagnosis
Setting:
Startup Device / RB: MODE_BLK.ACTUAL is OOS / Memory
failure / no GDC Communication / Startup GDC, data invalid /
Startup Sensor, data valid / Data Base doesn't match to FF
Software / MODE_BLK.PERMITTED doesn't include Auto /
MODE_BLK.TARGET is set OOS / GDC bold F message / GDC F
message / write from GDC to RB/TB doesn't work / Sensor
serial number / Sensor calibration date / GDC unit not
convertible to TB.prim_val / prim_val is outside range /
action: write from GDC to RB/TB / GDC Communication few
loss / no unit of GDC / GDC unit can't be converted to
TB.prim_range / a GDC value was not received / a GDC short
status is fatal or warn2 / PRIMARY_VALUE_1.status is
Uncertain / temperatur input / pressure input / p & T input /
unknown reason / Ok
Parameter
Parameter
Parameter
Parameter
DD name
Access
Description and settings
Initial Value