KROHNE GFC 300 FOUNDATION FIELDBUS - Manual (Page 35)

OPERATION
4
35
GFC 300
www.krohne.com 07/2012 - 4001866001 - AD GFC 300 FF R01 en
PRIMARY_VALUE_ PRIMARY_VALUE_ PRIMARY_VALUE_ PRIMARY_VALUE_
7777
density density density density
The measured density value and status available to the
Function Block.
-
STATUS
Status
R Digital transducers, unlike their analogue versions, can detect
faults that make the measurement bad or prevent the
actuator from responding. This additional, valuable
information will be passed along with each transmission of a
data value in the form of a status attribute.
-
VALUE
Value
R A numerical quantity entered by a user or calculated by the
algorithm.
-
PRIMARY_VALUE_ PRIMARY_VALUE_ PRIMARY_VALUE_ PRIMARY_VALUE_
RANGE_7 RANGE_7 RANGE_7 RANGE_7
density range density range density range density range
The high and low range limit values, the engineering units
code and the number of digits to the right of the decimal point
to be used to display the Primary Value.
-
EU_100
Engineering Unit
100
R The engineering unit value which represents the upper end of
range of the associated Block Parameter.
200
EU_0
Engineering Unit 0
R The engineering unit value which represents the lower end of
range of the associated Block Parameter.
0
UNITS_INDEX
Units Index
R/W Device Description units code index for the engineering unit
descriptor for the associated block value.
kg/m³
Settings:
kg/m³; Mg/m³; kg/dm³; g/cm³; g/m³; t/m³; kg/L; g/ml; g/L;
lb/in³; l/ft³; lb/gal; STon/yd³; lb/ImpGal
DECIMAL
Decimal (Point)
R The number of digits to the right of the decimal point which
should be used by an interface device in displaying the
specified parameter.
2
PRIMARY_VALUE_ PRIMARY_VALUE_ PRIMARY_VALUE_ PRIMARY_VALUE_
TYPE8 TYPE8 TYPE8 TYPE8
Primary Value Primary Value Primary Value Primary Value
Type8 Type8 Type8 Type8
R The type of measurement represented by the primary value.
For example: mass flow, absolute pressure, differential
temperature
flow speed
PRIMARY_VALUE_ PRIMARY_VALUE_ PRIMARY_VALUE_ PRIMARY_VALUE_
8888
flow speed flow speed flow speed flow speed
The measured flow speed value and status available to the
Function Block.
-
STATUS
Status
R Digital transducers, unlike their analogue versions, can detect
faults that make the measurement bad or prevent the
actuator from responding. This additional, valuable
information will be passed along with each transmission of a
data value in the form of a status attribute.
-
VALUE
Value
R A numerical quantity entered by a user or calculated by the
algorithm.
-
PRIMARY_VALUE_ PRIMARY_VALUE_ PRIMARY_VALUE_ PRIMARY_VALUE_
RANGE_8 RANGE_8 RANGE_8 RANGE_8
flow speed range flow speed range flow speed range flow speed range
The high and low range limit values, the engineering units
code and the number of digits to the right of the decimal point
to be used to display the Primary Value.
-
EU_100
Engineering Unit
100
R The engineering unit value which represents the upper end of
range of the associated Block Parameter.
100
EU_0
Engineering Unit 0
R The engineering unit value which represents the lower end of
range of the associated Block Parameter.
-100
UNITS_INDEX
Units Index
R/W Device Description units code index for the engineering unit
descriptor for the associated block value.
m/s
Settings:
m/s; mm/s; m/h; km/h; knot; in/s; ft/s; yd/s; in/min; ft/min;
yd/min; in/h; ft/h; yd/h; MPH
DECIMAL
Decimal (Point)
R The number of digits to the right of the decimal point which
should be used by an interface device in displaying the
specified parameter.
2
Parameter Parameter Parameter Parameter
DD name Access Description and settings Initial Value