KROHNE GFC 300 FOUNDATION FIELDBUS - Manual (Page 25)

OPERATION
4
25
GFC 300
www.krohne.com 07/2012 - 4001866001 - AD GFC 300 FF R01 en
Setting range for previous 2
parameters:
x_y_LIM
x_y_Limit
-3.39 E38…+3.39 E38 / - INF (- infinite) / + INF (+ infinite)
Setting for previous 2
parameters:
x_y_PRI
x_y_Priority
0: The associated alert may clear when the priority is changed
to 0, but it will never occur.
1: The associated alert is not send as a notification. If the
priority is above 1, then the alert must be reported.
2: Reserved for alerts that do not require the attention of a
plant operator, e.g. diagnostic and system alerts. Block alarm,
error alarm and update event have a fixed priority of 2.
3...7: Increasing higher priorities - advisory alarms.
8...15: Increasing higher priorities - critical alarms.
0
IO_OPTS IO_OPTS IO_OPTS IO_OPTS
IO Options IO Options IO Options IO Options
(IO = Input/Output) (IO = Input/Output) (IO = Input/Output) (IO = Input/Output)
R/W Options which the user may select to alter input and output
block processing.
Uninitialized
Setting:
Low Cutoff / Units Conversion
L_TYPE L_TYPE L_TYPE L_TYPE
Linearization Type Linearization Type Linearization Type Linearization Type
R/W Determines if the values passed by the TB to the AI block may
be used directly (Direct) or if the value is in different units and
must be converted linearly (Indirect) or with square root (Ind
Sqr Root), using the input range defined by the transducer and
the associated output range.
W = Writeable only by setting "OOS" in MODE_BLK
Uninitialized
Setting:
Uninitialized / Direct / Indirect / Ind Sqr Root
LO_ALM LO_ALM LO_ALM LO_ALM
Low Alarm Low Alarm Low Alarm Low Alarm
The status for Low Alarm and its associated time stamp.
Settings of 5 subelements see in the following part.
-
LO_LO_ALM LO_LO_ALM LO_LO_ALM LO_LO_ALM
Low Low Alarm Low Low Alarm Low Low Alarm Low Low Alarm
The status for Low Low Alarm and its associated time stamp.
Settings of 5 subelements see in the following part.
-
Settings of 5 subelements for previous 2 parameters Low Alarm and Low Low Alarm:
Unacknowledged R/W Setting:
Uninitialized / Acknowledged / Unacknowledged
Uninitialized
Alarm State R Setting:
Uninitialized / Clear - reported / Clear - not reported / Active -
reported / Active - not reported
Uninitialized
Time Stamp R Setting:
MM / DD / YY (Month / Day / Year)
HH:MM:SS (Hour:Minute:Second)
Uninitialized
Subcode R An enumeration specifying the cause of the alert to be
reported.
Other
Setting:
Other / Block Configuration / Link Configuration / Simulation
Active / Local Override / Device Fault State / Device
Maintenance / Input Failure / Output Failure / Memory
Failure / Lost Static Data / Lost NV Data / Readback Check /
Maintenance Needed / Power Up / Out Of Service
Value R A numerical quantity entered by a user or calculated by the
algorithm.
0.0
LO_LIM LO_LIM LO_LIM LO_LIM
Low Limit Low Limit Low Limit Low Limit
R/W The setting for Low Alarm in engineering units.
Setting range see in the following part.
(-NaN)
LO_LO_LIM LO_LO_LIM LO_LO_LIM LO_LO_LIM
Low Low Limit Low Low Limit Low Low Limit Low Low Limit
R/W The setting for Low Low Alarm in engineering units.
Setting range see in the following part.
(-NaN)
LO_PRI LO_PRI LO_PRI LO_PRI
Low Priority Low Priority Low Priority Low Priority
R/W Priority of the Low Alarm.
Setting see in the following part.
0
LO_LO_PRI LO_LO_PRI LO_LO_PRI LO_LO_PRI
Low Low Priority Low Low Priority Low Low Priority Low Low Priority
R/W Priority of the Low Low Alarm.
Setting see in the following part.
0
Parameter Parameter Parameter Parameter
DD name Access Description and settings Initial Value