Nstallation, Rocedures – Triton 8100 User/Installation Manual User Manual
Page 117
A-5
I
NSTALLATION
P
ROCEDURES
(b) Reach Depth More Than 10
inches (255 mm). Where the reach
depth to the operable parts of any con-
trol as measured from the vertical plane
perpendicular to the edge of the un-
obstructed clear floor space at the far-
thest protrusion of the automated
teller machine or surround is more than
10 inches (255 mm), the maximum
height above the finished floor or
grade shall be as follows:
S
N
O
I
T
A
C
I
F
I
C
E
P
S
Y
T
I
L
I
B
I
S
S
E
C
C
A
H
T
P
E
D
H
C
A
E
R
T
H
G
I
E
H
M
U
M
I
X
A
M
s
e
h
c
n
I
s
r
e
t
e
m
il
li
M
s
e
h
c
n
I
s
r
e
t
e
m
il
li
M
0
1
5
5
2
4
5
0
7
3
1
1
1
0
8
2
2
/
1
3
5
0
6
3
1
2
1
5
0
3
3
5
5
4
3
1
3
1
0
3
3
2
/
1
2
5
5
3
3
1
4
1
5
5
3
2
/
1
1
5
0
1
3
1
5
1
0
8
3
1
5
5
9
2
1
6
1
5
0
4
2
/
1
0
5
5
8
2
1
7
1
0
3
4
0
5
0
7
2
1
8
1
5
5
4
2
/
1
9
4
5
5
2
1
9
1
5
8
4
9
4
5
4
2
1
0
2
0
1
5
2
/
1
8
4
0
3
2
1
1
2
5
3
5
2
/
1
7
4
5
0
2
1
2
2
0
6
5
7
4
5
9
1
1
3
2
5
8
5
2
/
1
6
4
0
8
1
1
4
2
0
1
6
6
4
0
7
1
1
(3) Forward and Parallel Approach.
If both a forward and parallel approach
are possible, operable parts of controls
shall be placed within at least one of
the reach ranges in paragraphs (1) or
(2) of this section.
(4) Bins. Where bins are provided for
envelopes, waste paper, or other pur-
poses, at least one of each type pro-
vided shall comply with the applicable
reach ranges in paragraph (1), (2), or
(3) of this section.
EXCEPTION: Where a function can
be performed in a substantially
equivalent manner by using an alter-
nate control, only one of the controls
needed to perform that function is
required to comply with this section.
If the controls are identified by tac-
tile markings, such markings shall be
provided on both controls.
4.34.4 Controls.
Controls for user activation shall com-
ply with 4.27.4 (Operation).
4.34.5 Equipment for Persons with
Vision Impairments.
Instructions and all information for
use shall be made accessible to and
independently usable by persons
with vision impairments.
(20)
Where automated teller ma-
chines (ATMs) are provided, each
ATM shall comply with the require-
ments of 4.34 (Automated Teller Ma-
chines) except where two or more are
provided at a location, then only one
must comply.
EXCEPTION: Drive-up-only auto-
mated teller machines are not required
to comply with 4.27 (Controls and
Operating Mechanisms) and 4.34.3
(Reach Ranges).