Yokogawa Multi Channel Oxygen Analyzer System ZR22/AV550G User Manual
Page 54
A-5
IM 11M12D01-61E
TA0102-2.ai
AI3
AUTO
Relative
Index
Index
Parameter Name
Factory Default
Write
Mode
Explanation
AUTO
AUTO
AUTO
AUTO
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
—
0.0 (AI1)
0.0 (AI2)
0.0 (AI3)
0
—
—
0
—
AUTO
LOW_CUT
PV_FTIME
0sec (AI1)
0sec (AI2)
0sec (AI3)
HI_HI_LIM
FIELD_VAL
UPDATE_EVT
BLOCK_ALM
ALARM_SUM
ACK_OPTION
ALARM_HYS
HI_HI_PRI
HI_PRI
HI_LIM
LO_PRI
LO_LIM
LO_LO_PRI
1. #INF
AUTO
0xffff
0.5%
33
LO_LO_LIM
HI_HI_ALM
AUTO
AI1 AI2
4117
4118
4119
4120
4121
4122
4123
4124
4125
4126
4127
4128
4129
4130
4131
4132
4133
4017
4018
4019
4020
4021
4022
4023
4024
4025
4026
4027
4028
4029
4030
4031
4032
4033
Raw value of the field device in percent of thePV range,
with a status reflecting the Transducer condition, before
signal characterization (L_TYPE), filtering (PV_FTIME), or
low cut (LOW_CUT).
The block alarm is used for all configuration, hardware,
connection failure or system problems in the block. The
cause of the alert is entered in the subcode field. The first
alert to become active will set the Active status in the
Status attribute. As soon as the Unreported status is
cleared by the alert reporting task, another block alert may
be reported without clearing the Active status, if the
subcode has changed.
The current alert status, unacknowledged states,
unreported states, and disabled states of the alarms
associated with the function block.
Selection of whether alarms associated with the block will
be automatically acknowledged.
Amount the PV must return within the alarm limits before
the alarm condition clears. Alarm Hysteresis is expressed
as a percent of the PV span. 0 to 50
Priority of the high high alarm. 0, 1, 3 to 15
Priority of the high alarm. 0, 1, 3 to 15
The setting for high alarm in engineering units. (Note 1)
Priority of the low alarm. 0, 1, 3 to 15
The setting for the low alarm in engineering units.
(Note 2)
Priority of the low low alarm. 0, 1, 3 to 15
The setting of the low low alarm in engineering units.
(Note 2)
The status for high high alarm and its associated time stamp.
The status for high alarm and its associated time stamp.
The status of the low alarm and its associated time stamp.
The status of the low low alarm and its associated time
stamp.
This alert is generated by any change to the static data.
Sets low cut point of output. This low cut value become
available by setting "Low cutoff" to "IO_OPTS".
Time constant of a single exponential filter for the PV, in
seconds.
The setting for high high alarm in engineering units.
(Note 1)
—
—
—
—
AUTO
0
AUTO
AUTO
34
HI_ALM
4134
4034
35
LO_ALM
4135
4035
36
LO_LO_ALM
4136
4036
1. #INF
-1. #INF
0
-1. #INF
AUTO
—
—
—
—
Note 1: An intended set value can be written only if Min(OUT_SCALE.EU0, OUT_SCALE.EU100) ≤ the intended value ≤ +INF.
Note 2: An intended set value cannot be written if –INF ≤ the intended value ≤ Min(OUT_SCALE.EU0, OUT_SCALE.EU100).
4217
4218
4219
4220
4221
4222
4223
4224
4225
4226
4227
4228
4229
4230
4231
4232
4233
4234
4235
4236