Alpha Technologies AlphaNet IDH4 for XM2 and XM2-300HP Series - Technical Manual - Manual (Page 73)

73 746-257-B2-001, Rev. B (01/2014)
10.1 Definitions and Settings
10.0 Alpha MIB Parameters
Parameter OID Description Access Type Value
GENERAL CONTROLS
atiMgmtSysTamperPolarity 1.3.6.1.4.1.926.1.3.2.6.1.0 Determines when tamper is active Read/Write Integer 1=doorOpenWhenContactOpen
2=doorOpenWhenContactClosed
(default)
atiMgmtSysAlphaBusSize 1.3.6.1.4.1.926.1.3.2.6.2.0 Internal microprocessor communications
bus size. Alpha XM2 series power supplies
use 9 bit. Alpha GMX and VMX series
supplies use 8 bit
Read/Write Integer 1=9 Bit (Default)
2=8 Bit
atiMgmtSysGnrlInfoConfigs 1.3.6.1.4.1.926.1.3.2.7.1 Object Identifier
atiMgmtSysGnrlInfoConfigsMain 1.3.6.1.4.1.926.1.3.2.7.1.1.0 An ASCII string programmed into the main
board non-volatile memory.
Read Only Octet String Product number, configuration
number serial number, etc.
atiMgmtSysGnrlInfoConfigsDaughter 1.3.6.1.4.1.926.1.3.2.7.1.2.0 An ASCII string programmed into the C/D
battery circuitry.
Read Only Octet String Product number, configuration
number serial number, etc.
atiMgmtSysGnrlInfoConfigsBase 1.3.6.1.4.1.926.1.3.2.7.1.3.0 An ASCII string describing the base
configuration of the device.
Read Only Octet String i.e. DSM3, DSM3x, DPM, etc.
ENVIRONMENTAL I/O CONTROLLER
atiMgmtSysIo 1.3.6.1.4.1.926.1.3.2.8 Object Identifier
atiMgmtSysIoSelect 1.3.6.1.4.1.926.1.3.2.8.1 Indicates what function the IO pins are
being used for
Read/Write Integer 1 = Generic
2 = lapOnly
3 = heaterControlOnly
4 = generatorOnly
5 = heaterControlAndLap
6 = generatorAndLap
atiMgmtSysIoLAPState 1.3.6.1.4.1.926.1.3.2.8.2 Current state of the LAP device Read Only Integer 1: notInstalled(1)
2: ok(2)
3: acNotPresent(3)
4: lapBlown(4)
5: lapFail(5)
atiMgmtSysIoGenState 1.3.6.1.4.1.926.1.3.2.8.3 State of the DC Emergency Generator
when sense lines are used
Read Only Integer 1: notInstalled(1)
2: genOff(2)
3: genRunning(3)
4: genNotDetected(4)
5: error(5)
atiMgmtSysIoPinCtrl 1.3.6.1.4.1.926.1.3.2.8.20 Status of the ENV connector Output Pin
(Pin 3)
Read Only Integer 1 = Contact Open
2 = Contact Closed
atiMgmtSysIoPinIn4 1.3.6.1.4.1.926.1.3.2.8.21 Status of the ENV connector Input Pin#4 Read Only Integer 1 = Contact Open
2 = Contact Closed
atiMgmtSysIoPinIn5 1.3.6.1.4.1.926.1.3.2.8.22 Status of the ENV connector Input Pin#5 Read Only Integer 1 = Contact Open
2 = Contact Closed
atiMgmtSysIoPinIn6 1.3.6.1.4.1.926.1.3.2.8.23 Status of the ENV connector Input Pin#6 Read Only Integer 1 = Contact Open
2 = Contact Closed
PLATFORMS
atiProductPlatforms
1.3.6.1.4.1.926.1.4 Object Identifier
atiBroadbandUPS 1.3.6.1.4.1.926.1.4.1 Object Identifier
atiBBSysView 1.3.6.1.4.1.926.1.4.1.1 Object Identifier
atiBBSysViewSelects 1.3.6.1.4.1.926.1.4.1.1.1 Object Identifier
atiBBSysViewSelfTestControl 1.3.6.1.4.1.926.1.4.1.1.1.1.0 Starts/Stops a system self-test. Read/Write Integer 1=Stop
2=Start
atiBBSysViewSelfTestInhibit 1.3.6.1.4.1.926.1.4.1.1.1.2.0 System self-test is prevented. On reset,
the IDH4 gets this value from the master
XM2 (in a system with more than one
power supply).
Read/Write Integer 1=Normal (Default)
2=Inhibited
atiBBSysViewSystemControlMgr 1.3.6.1.4.1.926.1.4.1.1.1.3.0 If the System Control Manager is running,
the Small System Controller/Administrator
(SSC or SSA) is running and there is
coordination between the power supplies
for charging, testing, etc. The value of this
item is stored in non-volatile memory.
Read/Write Integer 1=Running
2=Disabled