Extron Electronics MKP 2000 - Manual (Page 27)

MKP 2000 Remote Control Panel • SIS ™ Operation MKP 2000 Remote Control Panel • SIS ™ Operation
SIS ™ Operation, cont’d
4-10 4-11
Command/r
esponse table for MKP SIS commands (continued)
Command
ASCII Command
Response
Additional description
(host to
M
K
P
)
(MKP t
o
host)
V
erbose mode Set verbose mode on
Esc
X9
CV
V
rb1
The MKP
reports all status changes to the device
that sent the command.
Read verbose mode
Esc
CV
X9
Read connection’s security level
Esc
CK
X1
0
Password level pr
otection assigned.
RS-232 port configuration
Configur
e serial port
Esc
X2
*
X1
1
,
X1
2
,
X1
3
,
X1
4
CP
Cpn
X2
•
Ccp
X1
1
*
X1
2
*
X1
3
*
X1
4
Example
:
Esc
1
*
9600
, n
, 8
, 1CP
Cpn01 •
Ccp9600,N,8,1
9600 baud, no parity
, 8 data bits, 1 stop bit.
V
iew port configuration
Esc
X2
Cp
X1
1
*
X1
2
*
X1
3
*
X1
4
Disable/enable inputs and outputs
Enable all inputs
Esc
+7BM
Upl
Enable all inputs.
Disable all inputs
Esc
+6BM
Upl
Disable all inputs.
Enable all outputs
Esc
+9BM
Upl
Enable all outputs.
Disable all outputs
Esc
+8BM
Upl
Disable all outputs.
Input and output enables
can
be r
ead using SIS commands, but the returned data is hard to interpr
et. Reading the enabled outputs is far
simpler using the HTML pages. See “System Settings page” in chapter 5, “HTML Operation.”
Command/r
esponse table for MKP SIS commands (continued)
Command
ASCII Command
Response
Additional description
(host to
M
K
P
)
(M
K
P
to host)
Information r
equests
Information r
equest
I
MKP
•
2000
Report model name.
Request for part number
N
60-682-00
See appendix
A
for part numbers.
Query firmware version
Q
X6
Show firmwar
e version
X6
in format
x
.xx
.
Query verbose firmwar
e version
0Q
X7
P
rovide a detailed status of the Ethernet pr
otocol
firmwar
e, the MKP
contr
oller firmware, and any
firmwar
e upgrade. The firmwar
e that is running is
marked by asterisk (
*).
A
caret (
^
) indicates that
the firmware has a bad checksum or an invalid load.
?.??
indicates that firmwar
e is not loaded.
Response description:
Ethernet pr
otocol firmware version
- controller firmwar
e version
- updated firmware version
Query status
S
X
8
Show voltage and temperature
r
eadings.
Resets
The Names Reset command (
Esc
ZXXX
) has no affect on an MKP 2000, but it can be applied fr
om a primary MKP 2000 to one or
mor
e connected MKP 3000s.
Names reset
Esc
ZXXX
Zpx
Erase all presets, pr
eset names, input names, and
output names.
Absolute r
eset
Esc
ZQQQ
Zpq
Perform a Names r
eset plus restoring all IP
settings.