Extron Electronics IPCP 505 User Guide - Manual (Page 64)

IPCP 505 • SIS Pr
ogramming and Contr
ol
58
Command/Response Table for SIS Commands (continued)
Command ASCII (Telnet)
(host to IPCP)
URL Encoded (web)
(host to IPCP)
Response
(IPCP to host)
Additional description
Configure serial port parameters 24 E X! * X2% , X2^ , X2& , X2* CP } X! = serial port number:
Serial ports: IR/serial ports:
01 = COM1 port 09 = IR/serial port 1
02 = COM2 port 10 = IR/serial port 2
03 = COM3 port 11 = IR/serial port 3
04 = COM4 port 12 = IR/serial port 4
05 = COM5 port 13 = IR/serial port 5
06 = COM6 port 14 = IR/serial port 6
07 = COM7 port 15 = IR/serial port 7
08 = COM8 port 16 = IR/serial port 8
X2% = baud rate (300-115200 baud, default
= 9600 baud).
X2^ = parity (O = odd, E = even,
N = none [default], M = mark, S = space).
X2&
= data bits: 7, 8 (default = 8).
X2* = stop bits: 1, 2 (default = 1).
W X! %2A X2% %2C X2^ %2C X2& %2C X2* CP |
Cpn X! •Ccp X2% , X2^ , X2& , X2* ]
Example: E 2*9600,N,8,1CP }
W2%2A9600%2CN%2C8%2C1CP |
Cpn02•Ccp9600,N,8,1 ] Set port 2 for 9600 baud, no parity,
8 data bits, and 1 stop bit.
View serial port parameters E X! CP } W X! CP | X2% , X2^ , X2& , X2* ]
Example E
2CP
}
9600,N,8,1
]
Configure mode 24 E X! * X2( CY } W X! %2A X2( CY | Cpn X! •Cty X2( ] X2( = serial port type:
0 = RS-232 (the only serial protocol
supported by COM1-COM6 ports, and the
default for COM7-COM8)
1 = RS-422
2 = RS-485.
View mode E X! CY } W X! CY | X2( ]
Configure flow control E X! * X3) , X3! CF } X3) = flow control
(H = hardware, S = software, N = none).
X3! = data pacing in milliseconds (0000 - 1000).
W X! %2A X3) %2C X3! CF | Cpn X! •Cfl X3) , X3! ]
View flow control 24 E X! CF } W X! CF | X3) , X3! ]
Configure receive timeout 24 E X! * X1& * X2) * X2# * X2! CE } Set the time to wait ( X1& = waiting time in
tens of ms until receipt of the first response
character before terminating the receive
operation,
X2) = waiting time in tens of ms
between characters before terminating) and
priority status.
(
X2# : 0 = default, use send data string
command parameters; 1 = use configure
receive timeout command parameters)
for port
X! . X2! = #L or #D (see previous
page). The response includes leading zeros.
W
X!
%2A
X1&
%2A
X2)
%2A
X2#
%2A
X2!
CE
|
Cpn X! •Cce X1& , X2) , X2# , X2! ]
View receive timeout E X! CE } W X! CE | X1& , X2) , X2# , X2! ]