Proxim ORiNOCO AP-2500 - Manual (Page 193)

193
Using the Command Line Interface
Parameter Control Commands
The following sections cover each CLI Command, and include several tables showing parameter properties. The two
Parameter Control Commands are show and set. These allow you to view (show) all parameters and statistics, and to
change (set) parameters.
•
show - To see any Parameter or Statistic values, you specify a single parameter, a Group, or a Table. Fore more
details, refer to "set and show command examples" later in this guide.
• set - Use this CLI Command to change parameter values. You can use a single CLI Statement to modify Tables, or
modify each parameter separately. Fore more details, refer to “set and show command examples” later in this
guide.
“set” and “show” Command Examples
In general, you will use the CLI "show" Command to view current parameter values, and use the CLI "set" Command
to change parameter values. As shown in the following six examples, parameters may be set individually, and all
parameters for a given table can be set with a single statement.
Example 1 - Set the Access Point IP Address Parameter
Syntax:
[Device Name]>set
Example:
[Device Name]>
set ipaddr 10.0.0.12
Result: IP Address will be changed when you reboot the Access Point. The CLI reminds you when rebooting is
required for a change to take effect. To reboot immediately, enter reboot 0 (zero) at the CLI prompt.
Example 2 - Create a table entry or row
Use 0 (zero) as the index to the table when creating an entry. When creating a table row, only the mandatory table
elements are required (comment is usually an optional table element). There are other optional table elements, which,
if not entered, the default value applies.
Syntax:
[Device Name]>set … Example:
[Device Name]> set mgmtipaccesstbl 0 ipaddr 10.0.0.10 ipmask 255.255.0.0Result: The IP Access Table (Index 0) “IP Address” and “IP Mask” parameters are assigned 10.0.0.10 and
255.255.0.0, respectively.NOTESome tables use a different syntax. See Working with Tables for details.Example 3 - Modify a table entry or rowUse the index to be modified and the table elements you would like to modify. For example, suppose the SNMP IP
Access table has one entry and you wanted to modify the IP Address:[Device Name]>set mgmtipaccesstbl 1 ipaddr 10.0.0.11You can also modify several elements in the table entry. Enter the index number and specific table elements you would
like to modify. Hint: Use the search Command to see the elements that belong to the table.[Device Name]>set mgmtipaccesstbl 1 ipaddr 10.0.0.12 submask 255.255.255.248 cmt “First Row” Pages: 1 … 191 192 193 194 195 … 250 wrong Brand wrong Model non readable See also other documents in the category Proxim Hardware: ORiNOCO AP-700 (242 pages) AP-4000 (235 pages) Stratum (4 pages) ORINOCO AP-2000 (244 pages) TSUNAMI MP.11 5012-SUR (24 pages) Sitemap
Example:
[Device Name]>
set mgmtipaccesstbl 0 ipaddr 10.0.0.10 ipmask 255.255.0.0
Result: The IP Access Table (Index 0) “IP Address” and “IP Mask” parameters are assigned 10.0.0.10 and
255.255.0.0, respectively.
NOTE
Some tables use a different syntax. See Working with Tables for details.
Example 3 - Modify a table entry or row
Use the index to be modified and the table elements you would like to modify. For example, suppose the SNMP IP
Access table has one entry and you wanted to modify the IP Address:
[Device Name]>set mgmtipaccesstbl 1 ipaddr 10.0.0.11
You can also modify several elements in the table entry. Enter the index number and specific table elements you would
like to modify. Hint: Use the search Command to see the elements that belong to the table.
[Device Name]>set mgmtipaccesstbl 1 ipaddr 10.0.0.12 submask 255.255.255.248
cmt “First Row”