MITSUBISHI ELECTRIC QJ71C24N - Manual (Page 117)

5 - 3 5 - 3
MELSEC-Q
5 DATA COMMUNICATION USING THE MELSEC COMMUNICATION
PROTOCOL
(2) System settings using the GX Configurator-SC
When it is necessary to change the default values registered in the Q series C24,
perform the settings as indicated in Chapter 8 and register these to the flash
ROM in the Q series C24.
• MC protocol system setting
• Transmission control and others system setting
POINT
To write from the external device to the intelligent function module installed in the
MELSECNET/H remote I/O station during communication using the MC protocol,
set the "Write allow/prohibit during PLC CPU RUN" in the GX Developer to enable.
5.1.4 Support of multiple CPU system or redundant system
When the external device accesses a QCPU in a multiple CPU system or redundant
system, it is possible to selectively access either a control or non-control CPU in the
multiple CPU system or a control or standby system CPU or System A or System B
CPU in the redundant system by specifying the target QCPU in "Requested module
I/O No." of the QnA compatible 4C frame for the MC protocol.
Refer to the Reference Manual for details.
Refer to Chapter 2 of this manual for the system configuration.
(Example) When multiple CPU No.1 is specified
F ram
e I
D
N
o .
46 H 05 H
S
e
lf -s
ta
ti o n
No
.
Co
m
m
a
n d
S
u
b com
m
an
d
D
e
vi
ce c
ode
H
e
ad
de
vi
ce
N
u
m
b
e r of
dev
ic
e
po
in
ts
S
u
m
c
h ec
k
co
de
38 H 30 H 33 H 30 H 33 H 45 H 30 H 30 H 30 H 30 H 30 H 30 H 34 H 30 H 31 H 30 H 30 H 30 H 31 H 58 H 2A H 30 H 30 H 30 H 30 H 34 H 30 H 30 H 30 H 30 H 35 H
H
F
L
8
H
0
L
7
H
0
L
0
H
0
L
0
H
0
L
0
H
0
L
1
H
0
L
1 X
L
0
L
5
PC No
.
—
0
—
0
H
0
—
0
—
4
H
0
—
0
—
0
—
4
—
3
—
0
—
0
—
0
E
N
Q
S
tat
io
n N
o
.
30 H 35 H
H
0
L
5
Ne
two
rk
No
.
30 H 37 H
H
0
L
7
—
E
33 H 36 H
H
3
L
6
R
e
qu
es
te
d m
o
d
u le
st
a
ti o
n N
o .
R
e
qu
es
te
d m
o
d
u le
I/
O
No
.
(Command massage of the QnA compatible 4C frame format 1)
REMARK
• When using the Q series C24 in a multiple CPU system, it is necessary to specify
the QCPU that controls the Q series C24 (hereinafter referred to as the control
PLC) using GX Developer.
• It is also possible to mount a Q series C24 of function version A in a multiple CPU
system. In this case, it is only possible to access the control PLC (PLC No.1).
• It is only possible to access the control PLC if data is communicated by means of
frames other than the QnA compatible 4C frame.