Fostex D2424 - Manual (Page 59)

Model D2424 Reference Manual (Chain Play function)
59
Setup of the Chain Play Mode
Upon setup of the previous “Chain Play List,” select the desired mode in the “Chain Play MD?” (Setup of the
chain play mode) menu in the same SETUP mode.
The chain play mode setting will be held even though power is switched off, and if power is switched when the
D2424 is set to pause mode, the recorder will automatically execute chain play. If chain play is no longer
required, reset to “
Off” the “ Chain Play MD? ” menu after ending chain play.
Specify the Program and Execute Chain Play
Specify at random a program set in the chain play list and execute chain play from the program specified.
This operation can be executed only when the “Chain Play MD?” menu is set in other than “Off.”
1. Press the [SETUP] key while the D2424 is in the stop
mode to switch to the SETUP display.
2. Display the “Chain Play MD?” menu via the [JOG] dial
and then press the [EXECUTE/YES] key.
The recorder will change to the display for setting up
of the chain play mode and the present setup mode
will flash (In the initial setup, “
Off ” will flash).
3. Select the desired mode via the [JOG] dial.
When the [ JOG ] dial is rotated, modes other than the
currently shown “ Off ” listed below can be selected.
“Off”
“Pause” (Pause mode)
“Auto P” (Auto play mode)
“Rpt” (Pepeat mode)
Refer to previous page 57 on
the function of each mode.
4. Press the [EXECUTE/YES] key after selecting the
mode.
The recorder will exit from the SETUP mode after setup
is completed.
In this step, if it was completed in the setup other
than the “
Off ” mode, the D2424 will automatically
locate to the “ AUTO RTN START point ” of the first
program in the previously setup “ Chain list ” and stop.
If it was completed after setup to “ Off ,” the D2424 will
return to the first display of the program prior to
entering the SETUP mode.).
If the D2424 is played back after this, functions of
the mode selected will be executed from the first
program in the chain list.
Normally, in chain play as explained above,
execution starts from the first program on the chain
list but any program of your choice can be specified
and chain play executed from that program.
For details, refer to “
Specify the program and execute
chain play ”.
1. Press the [PGM SEL] key while the D2424 is in the
stop mode.
After “ Select Chain No! ,” is displayed, the first number
in the present chain play list will flash and the
program, and its title, will be displayed.
2. Select the desired program with the [JOG] dial and
press the [EXECUTE/YES] key.
The sequence number currently set in the chain list
can be selected by rotating the [
JOG ] dial. The program
/title in selected order will be simultaneously
displayed. After selection, when the [
EXECUTE/YES ]
key is pressed, the D2424 will locate to the “ AUTO
RTN START point ” of the selected program.
3. Start playback by pressing the [PLAY] button.
Chain play will be execute in compliance to the
currently set “
Chain Play MD? ” mode.
∞ 42
OL
0
30
24
18
12
9
6
3
kHz
24
FS
BIT
SETUP
24
∞ 42
OL
0
30
24
18
12
9
6
3
23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
CLOCK
INT
∞ 42
OL
0
30
24
18
12
9
6
3
kHz
24
FS
BIT
SETUP
24
∞ 42
OL
0
30
24
18
12
9
6
3
23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
CLOCK
INT
∞ 42
OL 0
30
24
18
12 9
6
3
kHz
24
FS
BIT 24
∞ 42
OL 0
30
24
18
12 9
6
3
23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
CLOCK
INT
∞ 42
OL
0
30 24
18
12
9 6
3
kHz
24
FS
BIT
PGM
24
∞ 42
OL
0
30 24
18
12
9 6
3
SURE?
23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
CLOCK
INT
You cannot record or edit in the chain play mode.
It will only play back the program set in the chain
play list.
Flashing
Flashing
Be sure the Chain Play List is set up correctly be-
fore setting the chain play mode. Each setting of
the chain play mode except “Off,” will not function
if the previously mentioned “Chain play list” is not
set up correctly beforehand. If the mode is executed
while set up of with an incorrect list, after display-
ing “Illegal P.List!,” the D2424 will automatically
go to the previously mentioned “Chain Play List?”
menu.