Setup of the auto ee mode, Setup of the foot switch function, Setup of the auto ee mode (“auto ee mode?” menu) – Fostex D2424 User Manual
Page 123: Setting the operating clock, Flashing
123
Model D2424 Reference Manual (Changing the Initial Settings
To cancel the operation, or to restore the setting
obtained prior to the EXECUTE/YES key press, press
the STOP button or the EXIT/NO key. Each time you
press one of these keys, the recorder returns to the
previous hierarchy level of the menu, and finally exits
SETUP mode and displays the previous Time Base.
* For more information on audio files and events, refer
to the “Audio file and event” section of the ”Before
Starting” chapter.
3.Use the JOG dial to select another (01-24) to check
the number of events on the corresponding track.
4.Press the EXIT/NO key or the STOP button
repeatedly to exit SETUP mode.
Flashing
Setup of the Auto EE mode (“Auto EE Mode?” menu)
At the “Setup of Auto EE mode” menu, you must set up whether it should be automatically set to "
ALL INPUT
monitor
" or not when D2424 is in the STOP mode.
1.While the recorder is stopped, press the [SETUP]
key to enter SETUP mode.
2.Turn the [JOG] dial to select “Auto EE Mode ?”
(“?” flashes), then press the [EXECUTE/YES] key.
A flashing “
?
” will extinguish by pressing the [
EXECUTE/
YES
] key and the auto EE mode information that was lit
will being flashing. Initial setting, it will show “
Off
”.
• Initial setting:
[Off]
• Device ID:
[Off] or [On]
* This setting is shared by all Programs in the same disk.
* The settings cannot be saved and loaded as part of the song data.
* The settings are maintained after you turn off the power to the recorder.
3.With the [JOG] dial, select the auto EE mode.
4. After selecting "On" or "Off," press the [EXECUTE/
YES] key again.
The selected On/Off will be registered and the Step-2
"
?
" will return to flashing.
5.Press the [EXIT/NO] key or the [STOP] button
repeatedly to exit SETUP mode.
To cancel the operation, or to restore the setting
obtained prior to the [EXECUTE/YES] key press, press
the [STOP] button or the [EXIT/NO] key. Each time
you press one of these keys, the recorder returns to
the previous hierarchy level of the menu, and finally
exits SETUP mode and displays the previous Time Base.
Setting the operating clock
∞
42
OL
0
30
24
18
12
9
6
3
kHz
24
FS
BIT
SETUP
24
∞
42
OL
0
30
24
18
12
9
6
3
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
CLOCK
INT
∞
42
OL
0
30
24
18
12
9
6
3
kHz
24
FS
BIT
SETUP
24
∞
42
OL
0
30
24
18
12
9
6
3
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
CLOCK
INT
Setup of the Foot switch function (“Foot SW?” menu)
At the “Setup of the foot switch function” menu, functions of a foot switch connected to the FOOT SW jack
must be set up.
Functions of the foot switch are, manual punch in/out or PLAY-STOP of D2424. Initially, this is set to the
"
Punch in/out function
" explained in "
Using the foot switch for manual punch in/out
," page
41
. You can change this
to PLAY-STOP of the recorder if you so wish.
• Initial setting:
[Punch IO]
• Option:
[Punch IO] (Punch in/out function) or [PLY/STP] (Play/stop function)
* This setting is shared by all Programs in the same disk.
* The settings cannot be saved and loaded as part of the song data.
* The settings are maintained after you turn off the power to the recorder.