Warning messages, Model d2424 reference manual (names and functions) – Fostex D2424 User Manual
Page 22
Model D2424 Reference Manual (Names and Functions)
22
6. Warning messages
If you perform an incorrect operation, input
incorrect data, or if an error occurs, the following
alarm indication appears:
Invalid data indication:
The input data is not appropriate for the operation.
Invalid In/Out indication:
The In or Out point is not appropriate for the operation.
You can select the desired Program from the
already setup Programs by rotating the [JOG] dial
while the Program number and “SURE ?” are
flashing.
After you select a Program, press the [EXECUTE/
YES] key to return to the selected Program’s ABS
indication.
The Time Base display will indicate the selected
Program’s Time Base, since you can set the Time
Base for each Program individually.
To change the Time Base display after you have
selected the desired Program, press the [DISP SEL]
key while holding down the [SHIFT] key.
Pressing only the [DISP/SEL] key will take you to
the REMAIN display based on the current Time
Base.
• The maximum record time of the program is
dependent on the permissible record time (size) of
the hard disk, regardless of how many programs are
created on the disk. If, for example, there is roughly
30 minutes of record time remaining (REMAIN) on
the current drive immediately after it is formatted,
and a 20 minute program is recorded in Program 1,
then there is only 10 minutes of recording time
remaining for any additional programs.
Simply put, if the total record time is 30 minutes it
does not matter whether the 30 minutes is taken by 1
program or shared among several programs, since
the total of 30 minutes for a recording remains the
absolute total.
Note that some disk space is compensated when
several programs are created on the disk. A new
program cannot be created when there is no
recordable space remaining on the disk. However,
programs produced by "Program duplicating" are
exempted.
• For initial setup, when producing a new program, the
initial setting of the currently active program is
directly copied. For example, if there is a randomly
set tempo map in the current program, that tempo
map setting will be copied as the tempo map for the
new program. This is convenient for producing a
new program with the same setting as previously
made music.
Display of void:
This is displayed if you attempt some sort of process for
which the optional Model 8345 TC/SYNC card is
necessary and is not installed.
Action to take:
Input correct data.
Action to take:
Input correct data.
∞
42
OL
0
30
24
18
12
9
6
3
kHz
24
FS
BIT
24
∞
42
OL
0
30
24
18
12
9
6
3
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
CLOCK
INT
∞
42
OL
0
30
24
18
12
9
6
3
kHz
24
FS
BIT
24
∞
42
OL
0
30
24
18
12
9
6
3
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
CLOCK
INT
∞
42
OL
0
30
24
18
12
9
6
3
kHz
24
FS
BIT
24
∞
42
OL
0
30
24
18
12
9
6
3
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
CLOCK
INT
∞
42
OL
0
30
24
18
12
9
6
3
kHz
24
FS
BIT
24
∞
42
OL
0
30
24
18
12
9
6
3
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
CLOCK
INT
Overtime indication:
Available disk space is insufficient for the length of time
(the number of measures) indicated on the display.)
Action to take:
During the copy & paste and move & paste operation,
try to shorten the length of the copied data by the
indicated amount. Alternatively, use the “ERASE”
function to move the ABS END point backward to obtain
enough disk space for editing.
Optimizing the disk is necessary in the current drive
in which multiple undo is ON.
F
S
M
H
∞
42
OL
0
30
24
18
12
9
6
3
kHz
24
FS
BIT
24
∞
42
OL
0
30
24
18
12
9
6
3
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
CLOCK
INT
Unassigned track indication:
Select any track.
Action to take:
Use the RECORD TRACK select key to ready any track.
∞
42
OL
0
30
24
18
12
9
6
3
kHz
24
FS
BIT
24
∞
42
OL
0
30
24
18
12
9
6
3
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
CLOCK
INT