Fostex D2424 - Manual (Page 11)

Model D2424 Reference Manual (Names and Functions)
11
1. Controller Connection Cable
Connect this cable to the recorder controller
connection jack.
2. Record track select key
[RECORD TRACK/ENVELOPE]
"SAFE-READY" of the recording track can be selected
(The track can be selected by shifting to 1-8, 9-16
or 17-24 with the [TRACK SHIFT] key.
If the select key is pressed once, that track will be in
the READY state and the track display ( ) will blink.
It will change to SAFE if pressed again and the track
display will be extinguished.
When recording is started from the READY mode,
the blinking track display will light.
If the [RECORD] button only is pressed from the
READY mode, the READY track only will enter input
monitor mode, and the recording level can be
adjusted. If the [RECORD] button is pressed once
again, the D2424 will return to repro monitoring.
If any select key is pressed together with the [SHIFT]
key, the envelope function of that track can be
executed. This key is also used for editing such as
copy paste, move paste and erase.
* Refer to page “ 28 ” for details about the reproduction
monitor and the input monitor.
* Refer to page “ 60 ” for details about the envelope
function.
* Refer to page “ 66 ” for details about the copy/paste
and move/paste function.
3. Track shift key [TRACK SHIFT/ALL INPUT]
When selecting a recording track, this is pressed to
shift to the selectable track. With each pressing of
the key, the TRACK SHIFT LED will sequentially
switch in order of: "Extinguish" - "Lighting of 9-16"
- "Lighting of 17-24" - "Extinguish" to indicate the
modes listed below
Auto Return/ Auto Play mode is OFF.
(No indication)
AUTO RTN
AUTO PLAY
AUTO RTN
AUTO PLAY
AUTO RTN
AUTO PLAY
AUTO RTN
AUTO PLAY
Auto Play mode:
In this mode, playback will start automatically after the
START point is located. This function is effective at any
locate points other than the REC END point.
Auto Return mode:
When the END point is reached during playback, the START
point is automatically located in this mode. This function
is effective only when the START and END points have
been specified.
Detachable Controller section
The Auto Return function is works only during playback.
In the recording mode, the START point will not be
located automatically when the END point is reached.
4. Auto Play/Auto Return key [AUTO RTN/PLAY]
Pressing this key repeatedly will change Auto Play
mode, Auto Return mode, and Repeat mode On/Off
as follows: ( : LED off, : LED light up)
Auto Play mode is ON.
(Only the AUTO PLAY LED is lit. )
Auto Return mode is ON.
(Only the AUTO RTN LED is lit. )
Auto Repeat mode is ON.
(Both AUTO PLAY and AUT RTN LEDs are lit. )
* All TRACK SHIFT LED extinguished: Tracks 1-8 can be selected.
* "9-16" are lighted: Tracks 9-16 can be selected.
* "17-24" are lighted: Tracks 17-24 can be selected.
All real track input monitors can be switch on or off
each press of this key while pressing [SHIFT] key.
When all tracks are set to input monitor, the ALL
INPUT LED will light.
HOLD
RECORD STOP PLAY REW F FWD
ALL INPUT ALL READY
LOCATE REC END
VARI PITCH PUNCH LOCATE REHEARSAL
TAKE
RECALL STORE
EXIT/NO EXECUTE/YES PGM SEL
NEXT PREV UNDO/REDO
PREVIEW
EDIT SETUP
AUTO RTN
OUT IN AUTO PLAY START OUT IN END
17-24 ACCESS 9-16
1/9/17 2/10/18 3/11/19 4/12/20 5/13/21 6/14/22 7/15/23 8/16/24
FOOT SW
LOCATE ABS 0
CLIPBOARD PLAY
AUTO
TRACK SHIFT
SHIFT
DISP SEL
CHARACTER
TIME BASE SEL
P.EDIT
EJECT
ENVELOPE
CHASE
TC READY TC GEN M.UNDO
TRACK SHIFT
PREV TC NEXT TC
RECORD TRACK
CLIPBOARD AUTO PUNCH
AUTO RTN
LOCATE MEMORY
24bit
96kHz
OPTICAL
24TRACK DIGITAL RECORDER
1 2 3 4 5 6 7 8 9 10
11
12
13
14 15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
34 32 33
35
36