Sony Ultra Wide Converter For SEL16F28 and SEL20F28 User Manual
Page 87
6. Menu Display and Settings: Paint Menu
87
Paint >Knee
Sets knee correction settings.
Item
Sub-item setting
Description
Setting
On
/ Off
Turns the knee correction function on/
off.
(Enabled when Gamma >Gamma
Category is set to STD)
Auto Knee
On
/ Off
Turns the auto knee correction function
on/off.
Point
75% to 109% (
90%
)
Sets the knee point.
Slope
–99 to +99 (
±0
)
Sets the knee slope.
Knee
Saturation
On
/ Off
Enables/disables knee saturation
adjustment (adjusts coloring above the
knee point).
[Note]
The Black Gamma and Knee >Knee Saturation
functions cannot be used at the same time.
Knee
Saturation
Level
–99 to +99 (
±0
)
Sets the level for adjusting the coloring
above the knee point (knee saturation).
Paint >White Clip
Sets white clip adjustment settings.
Item
Sub-item setting
Description
Setting
On
/ Off
Turns the white clip adjustment function
on/off.
(Enabled when Gamma >Gamma
Category is set to STD)
[Note]
The setting is reset to On when the camcorder
is turned off. To set to Off permanently, set
Level to 109%.
Level
90.0% to
109.0%
Sets the white clip level.
Paint >Detail(QFHD)
Sets detail (QFHD) adjustment settings.
Item
Sub-item setting
Description
Setting
On
/ Off
Turns the detail adjustment function on/
off.
Level
–99 to +99 (
±0
)
Sets the detail level.
H/V Ratio
–99 to +99 (
±0
)
Sets the mix ratio between the H detail
level and the V detail level.
Paint >Detail(QFHD)
Sets detail (QFHD) adjustment settings.
Item
Sub-item setting
Description
Crispening
–99 to +99 (
±0
)
Sets the crispening level.
Frequency
–99 to +99 (
±0
)
Sets the center frequency of the detail
(detail thickness).
The detail is thinner the higher the center
frequency, and thicker the lower the
center frequency.
Knee
Aperture
On /
Off
Turns the knee aperture correction
function on/off.
Knee
Aperture
Level
–99 to +99 (
±0
)
Sets the knee aperture level.
White Limit
–99 to +99 (
±0
)
Sets the white-side detail limiter.
Black Limit
–99 to +99 (
±0
)
Sets the black-side detail limiter.
V Detail
Creation
NAM / Y / G /
G+R
Sets the signal source for creating the V
detail to NAM (G or R, whichever is
higher), Y, G, or G+R.
Paint >Detail(HD)
Sets detail (HD) adjustment settings.
Item
Sub-item setting
Description
Setting
On
/ Off
Turns the detail adjustment function on/
off.
Level
–99 to +99 (
±0
)
Sets the detail level.
H/V Ratio
–99 to +99 (
±0
)
Sets the mix ratio between the H detail
level and the V detail level.
Crispening
–99 to +99 (
±0
)
Sets the crispening level.
Frequency
–99 to +99 (
±0
)
Sets the center frequency of the detail
(detail thickness).
The detail is thinner the higher the center
frequency, and thicker the lower the
center frequency.
Knee
Aperture
On /
Off
Turns the knee aperture correction
function on/off.
Knee
Aperture
Level
–99 to +99 (
±0
)
Sets the knee aperture level.
White Limit
–99 to +99 (
±0
)
Sets the white-side detail limiter.