Sony Ultra Wide Converter For SEL16F28 and SEL20F28 - Manual (Page 56)

4. Network Functions 56
High-quality streaming is supported by
enabling network client mode and connecting
a Sony Network RX Station (option) as
a Connection Control Manager (CCM) or
connecting via XDCAM air.
Setting the Network Client Mode
Connection
Up to three network client mode connections
can be configured as NCM Settings.
1
Select Network Client Mode >NCM
Settings1 (or NCM Settings2, NCM
Settings3) in the Network menu.
The network client mode connection
destination setup screen appears.
2
Set each item on the connection
destination setup screen.
Display Name
Set the display name in the NCM Settings
menu.
CCM Address
Enter the address of the CCM to connect
(host name or IP address).
CCM Port
Enter the port number of the CCM to
connect.
User Name
Enter the user name.
Password
Enter the password.
CCM Certificate
A CCM root certificate is required to
connect to a CCM or to XDCAM air. The
camcorder contains a built-in CCM root
certificate, which can also be updated. To
update the CCM root certificate, save the
certificate on a memory card and then
import the certificate from the memory
card.
ˎ ˎ Load
Select Set in step 3 to import a
certificate.
* The certificate to be loaded must be in PEM
format, and should be written to the root
directory of the SD card with “CCM_certification.
pem” file name.
ˎ ˎ Clear
Select Set in step 3 to clear a certificate.
ˎ ˎ None
Do not load or clear a certificate.
[Notes]
ˎ ˎ Set the clock of the camcorder to the correct time
before loading CCM and XDCAM air connection
certificates.
ˎ ˎ When recording in XAVC-I 3840×2160P 59.94/50P,
Load cannot be selected.
ˎ ˎ In low voltage state, CCM and XDCAM air
connection certificates cannot be loaded or
cleared.
CCM Certificate Status
Displays the load status of the certificate.
Camera Control
Enable/disable camera control when
connected with a CCM.
Camera Setting
Enable/disable ALL file operations when
connected with a CCM.
Reset
Reset the settings of NCM Settings to the
defaults.
3
When finished, select Set to apply the
settings.
Always select Set after changing the
settings. The settings are not applied if
Set is not selected.
4
Select Network Client Mode >NCM
Settings Select in the Network menu, and
then select the NCM settings (NCM
Settings1, NCM Settings2, NCM Settings3)
specified in steps 1 to 3.
Setting the Streaming Quality
Set Network Client Mode >Streaming Quality
(page 105) in the Network menu to High for
high-quality streaming. Set Streaming Quality
to Normal for normal quality.
[Notes]
ˎ ˎ Streaming Quality cannot be set to High in the
following cases.
– When Proxy Rec >Setting (page 81) in the
Project menu is set to On
– When 4K & HD (Sub) Rec >Setting (page 81) in
the Project menu is set to On
– When Focus >Face Detection AF (page 77) in the
Shooting menu is not set to Off
– When Network Client Mode >Setting (page 104)
in the Network menu is set to On
ˎ ˎ When Network Client Mode >Setting (page 104)
in the Network menu is set to On, Streaming Quality
cannot be changed.
Connecting in Network Client
Mode
1
Connect the camcorder to the Internet as
described in “Connecting to the Internet”
(page 52).
2
Set Network Client Mode >Setting in the
Network menu to On.
Network client mode is enabled, and the
camcorder connects to the Network RX
Station or XDCAM air.
Live streaming starts in response to
Network RX Station operation. For details
about operation, refer to the instruction
manual for the Network RX Station or the
Help for XDCAM air.
You can also set Setting to On or Off by
pressing an assignable button
(page 41) assigned with Network Client
Mode.
[Notes]
ˎ ˎ Streaming cannot be started under the following
menu settings.
– When S&Q Motion >Setting in the Shooting menu
is set to On
– When Interval Rec >Setting in the Project menu is
set to On
– When Simul Rec >Setting in the Project menu is
set to On
ˎ ˎ After changing to network client mode, monitoring
(page 59) is not available.
ˎ ˎ Changing to network client mode while monitoring
will stop the monitoring.
ˎ ˎ File transfer is not supported during streaming in
network client mode. File transfer is supported after
stopping streaming.
ˎ ˎ If streaming in network client mode is started during
file transfer, the file transfer stops. File transfer
restarts after stopping streaming.
ˎ ˎ User Name, Password, and certificates are not saved
in an ALL file, so these must be configured again after
loading an ALL file.
ˎ ˎ If Setting is set to Off while streaming in network
client mode, streaming stops.
ˎ ˎ When streaming in network client mode, NCM
Settings Select and the NCM Settings selected using
NCM Settings Select cannot be changed.
ˎ ˎ During streaming, the screen information update
frequency is reduced, but this does not affect
operation.
ˎ ˎ The recording settings cannot be changed during
streaming in network client mode.
ˎ ˎ The wired LAN settings cannot be changed during
streaming in network client mode.
ˎ ˎ The image may momentarily stop when switching to
the thumbnail screen or playback screen during QoS
streaming.
ˎ ˎ The distribution formats available for streaming
vary depending on the Rec Format setting of the
camcorder.
Using Network Client Mode