ProSoft Technology MVI69-101S User Manual
User manual
Table of contents
Document Outline
- Start Here
- To install ProSoft Configuration Builder from the ProSoft Web Site
- To install ProSoft Configuration Builder from the Product CD
- If RSLogix is unable to establish communication with the processor, follow these steps:
- Configuring the MVI69-101S Module
- To add a project to an existing project file:
- To add a module to your project:
- To add a module to a different location:
- To rename an object:
- To configure module parameters
- To add comments to your configuration file:
- To print a configuration file:
- [Backplane Configuration]
- [IEC-870-5-101 Port 0]
- Enabled
- Time DB Offset
- Data Link address
- Data Link address Length
- Common address of ASDU
- Common address of ASDU Len
- Inform. Object address Len
- Select/Operate Timeout
- Cyclic Data Transmission
- Use ACTTERM with Setpoint
- Use ACTTERM with Step
- Single Char ACK F0, 1 or 3
- Single Char ACK C1 or C2
- Maximum ASDU Resp Len
- Cause of Trans Octets
- Freeze Start Type
- Interval for Freeze
- Set Priority Queues
- Cyclic Set IV Time
- IV Check Delay Time
- IV Fail Count
- Event Scan Delay
- Scan Events
- Time Type
- Use Balanced Mode
- Retry Count
- Response Timeout
- Baud Rate
- Parity
- RTS On
- RTS Off
- Minimum Delay
- Receive Timeout
- Backup Port Enabled
- Backup Port Baud Rate
- Backup Port Parity
- Backup Port RTS On
- Backup Port RTS Off
- Backup Port Min Delay
- Backup Port Handshaking
- [IEC-870-5-101 Database]
- [M_SP_NA_1]
- [M_DP_NA_1]
- [M_ST_NA_1]
- [M_ME_NA_1]
- [M_ME_NB_1]
- [M_ME_NC_1]
- [M_IT_NA_1]
- [C_SC_NA_1]
- [C_DC_NA_1]
- [C_RC_NA_1]
- [C_SE_NA_1]
- [C_SE_NB_1]
- [C_SE_NC_1]
- Download the Project to the Module
- To Download the Project File
- Ladder Logic
- Diagnostics and Troubleshooting
- Reading Status Data from the Module
- Required Hardware
- The Configuration/Debug Menu
- Main Menu
- Viewing Block Transfer Statistics
- Opening the Data Analyzer Menu
- Viewing Module Configuration
- Opening the Database Menu
- Viewing Error and Status Data
- Viewing Port Configuration
- Receiving the Configuration File
- Sending the Configuration File
- Viewing Version Information
- Warm Booting the Module
- Viewing Data Type Setup
- Viewing IEC 60870 Database Configuration
- Exiting the Program
- Database View Menu
- Viewing Register Pages
- Displaying the Current Page of Registers Again
- Moving Back Through 5 Pages of Registers
- Viewing the Previous 100 Registers of Data
- Skipping 500 Registers of Data
- Viewing the Next 100 Registers of Data
- Viewing Data in Decimal Format
- Viewing Data in Hexadecimal Format
- Viewing Data in Floating Point Format
- Viewing Data in ASCII (Text) Format
- Returning to the Main Menu
- Data Analyzer
- Analyzing Data for the first application port
- Analyzing Data for the second application port
- Displaying Timing Marks in the Data Analyzer
- Removing Timing Marks in the Data Analyzer
- Viewing Data in Hexadecimal Format
- Viewing Data in ASCII (Text) Format
- Starting the Data Analyzer
- Stopping the Data Analyzer
- Returning to the Main Menu
- Data Analyzer Tips
- LED Status Indicators
- Reading Status Data from the Module
- Reference
- Example - Changing the ASDU Length:
- Example - Periodic Monitor Polling:
- Example - General Interrogation
- Example - Mode A
- Example I - Freeze Start Type
- Example II - Freeze Start Type
- Example - Monitor Point Configuration for Command Points:
- Example - Parameter Data for Monitored Points:
- Example - Event Priority
- Support, Service & Warranty
- Index