List of operating parameters – HEIDENHAIN PT 855 for Turning User Manual
Page 63
II - 2
Operating Parameters
POSITIP 855
Technical Information
65
✍
✍
✍
✍
✍
List of operating parameters
Parameter
Page
Function and
Numerical
allowed entries
entry
*
P 1
mm/inch
72
Dimensions in millimeters: mm •
0
P 1 ..............
16
Dimensions in inches: inch
1
P 3.1 Radius/diameter 1
72
Radius display
0
P 3.1 ...........
P 3.3 Radius/diameter 3
17
Diameter display
1
P 3.3 ...........
P 5.1 Separate/sum 1
72
Separate value display
0
P 5.1 ...........
P 5.3 Separate/sum 3
17
Sum display
1
P 5.3 ...........
P 11
Scaling factor OFF/ON
55
Scaling factor inactive: OFF
0
P 11 ............
Scaling factor active: ON
1
P 12.1 Scaling factor 1
55
Scaling factor
P 12.1 .........
P 12.3 Scaling factor 3
0.1 to 9.999 999
1.0
P 12.3 .........
P 14
Oversize OFF/ON
22
Oversize inactive: OFF
0
P 14 ............
Oversize active: ON
1
P 15.1 Oversize 1
22
Amount of oversize
P 15.1 .........
P 15.3 Oversize 3
– 199.999 to + 199.999 [mm]
0.0
P 15.3 .........
P 23
Display freeze
78
Ignore signal: Off
0
P 23 ............
Influence position display by signal
Stop display: Concrnt
1
for measured value output
Freeze display: Frozen
2
P 30.1 Counting direction 1
69
Positive counting direction
0
P 30.1 .........
P 30.2 Counting direction 2
with positive traverse direction
P 30.2 .........
P 30.3 Counting direction 3
Negative counting direction
1
P 30.3 .........
P 30.4 Counting direction 4
with positive traverse direction
P 30.4 .........
P 31.1 Signal period 1
70
Signal period of linear encoder
20
P 31.1 .........
P 31.2 Signal period 2
(see operating instructions for
P 31.2 .........
P 31.3 Signal period 3
encoder)
P 31.3 .........
P 31.4 Signal period 4
P 31.4 .........
P 32.1 Linear subdivision 1
70
Linear subdivision of the
20
P 32.1 .........
P 32.2 Linear subdivision 2
encoder signals
P 32.2 .........
P 32.3 Linear subdivision 3
P 32.3 .........
P 32.4 Linear subdivision 4
P 32.4 .........
P 40.1 Error compensation 1
73
No axis error compensation: OFF
0
P 40.1 .........
P 40.2 Error compensation 2
Linear axis error comp.: Linear
1
P 40.2 .........
P 40.3 Error compensation 3
Non-linear axis error
2
P 40.3 .........
P 40.4 Error compensation 4
compensation: Non-linear
P 40.4 .........
P 41.1 Linear compensation 1
73
Amount of a linear axis error
+0.0
P 41.1 .........
P 41.2 Linear compensation 2
compensation [ppm]
P 41.2 .........
P 41.3 Linear compensation 3
P 41.3 .........
P 41.4 Linear compensation 4
P 41.4 .........
P 43.1 Distance coding 1
68
No distance coding: None
0
P 43.1 .........
P 43.2 Distance coding 2
500
×
GP, 1000
×
GP
500,
1000
P 43.2 .........
P 43.3 Distance coding 3
2000
×
GP, 5000
×
GP
2000, 5000
P 43.3 .........
P 43.4 Distance coding 4
P 43.4 .........
P 44.1 Reference mark 1
68
Evaluate reference marks: Yes
0
P 44.1 .........
P 44.2 Reference mark 2
Do not evaluate: No
1
P 44.2 .........
P 44.3 Reference mark 3
P 44.3 .........
P 44.4 Reference mark 4
P 44.4 .........
*
Standard factory settings are in bold italics