H3C Technologies H3C S10500 Series Switches - Manual (Page 162)

151
{
Ten-GigabitEthernet 1/0/6 through Ten-GigabitEthernet 1/0/8.
{
Ten-GigabitEthernet 2/0/5 through Ten-GigabitEthernet 2/0/8.
[SwitchA] interface ten-gigabitethernet 1/0/6
[SwitchA-Ten-GigabitEthernet1/0/6] priority-flow-control enable
[SwitchA-Ten-GigabitEthernet1/0/6] priority-flow-control no-drop dot1p 3
[SwitchA-Ten-GigabitEthernet1/0/6] qos trust dot1p
[SwitchA-Ten-GigabitEthernet1/0/6] quit
[SwitchA] interface ten-gigabitethernet 1/0/7
[SwitchA-Ten-GigabitEthernet1/0/7] priority-flow-control enable
[SwitchA-Ten-GigabitEthernet1/0/7] priority-flow-control no-drop dot1p 3
[SwitchA-Ten-GigabitEthernet1/0/7] qos trust dot1p
[SwitchA-Ten-GigabitEthernet1/0/7] quit
[SwitchA] interface ten-gigabitethernet 1/0/8
[SwitchA-Ten-GigabitEthernet1/0/8] priority-flow-control enable
[SwitchA-Ten-GigabitEthernet1/0/8] priority-flow-control no-drop dot1p 3
[SwitchA-Ten-GigabitEthernet1/0/8] qos trust dot1p
[SwitchA-Ten-GigabitEthernet1/0/8] quit
[SwitchA] interface ten-gigabitethernet 2/0/5
[SwitchA-Ten-GigabitEthernet2/0/5] priority-flow-control enable
[SwitchA-Ten-GigabitEthernet2/0/5] priority-flow-control no-drop dot1p 3
[SwitchA-Ten-GigabitEthernet2/0/5] qos trust dot1p
[SwitchA-Ten-GigabitEthernet2/0/5] quit
[SwitchA] interface ten-gigabitethernet 2/0/6
[SwitchA-Ten-GigabitEthernet2/0/6] priority-flow-control enable
[SwitchA-Ten-GigabitEthernet2/0/6] priority-flow-control no-drop dot1p 3
[SwitchA-Ten-GigabitEthernet2/0/6] qos trust dot1p
[SwitchA-Ten-GigabitEthernet2/0/6] quit
[SwitchA] interface ten-gigabitethernet 2/0/7
[SwitchA-Ten-GigabitEthernet2/0/7] priority-flow-control enable
[SwitchA-Ten-GigabitEthernet2/0/7] priority-flow-control no-drop dot1p 3
[SwitchA-Ten-GigabitEthernet2/0/7] qos trust dot1p
[SwitchA-Ten-GigabitEthernet2/0/7] quit
[SwitchA] interface ten-gigabitethernet 2/0/8
[SwitchA-Ten-GigabitEthernet2/0/8] priority-flow-control enable
[SwitchA-Ten-GigabitEthernet2/0/8] priority-flow-control no-drop dot1p 3
[SwitchA-Ten-GigabitEthernet2/0/8] qos trust dot1p
[SwitchA-Ten-GigabitEthernet2/0/8] quit
5. Configure ETS:
# Configure the 802.1p-local priority mapping table as follows:
{
Map 802.1p priority value 3 to local precedence 1.
{
Map the other 802.1p priority values to local precedence 0.
[SwitchA] qos map-table dot1p-lp
[SwitchA-maptbl-dot1p-lp] import 3 export 1
[SwitchA-maptbl-dot1p-lp] import 0 export 0
[SwitchA-maptbl-dot1p-lp] import 1 export 0
[SwitchA-maptbl-dot1p-lp] import 2 export 0
[SwitchA-maptbl-dot1p-lp] import 4 export 0