H3C Technologies H3C S12500 Series Switches User Manual

Page 96

[DeviceC-GigabitEthernet3/0/3] link-delay 0

[DeviceC-GigabitEthernet3/0/3] undo stp enable

[DeviceC-GigabitEthernet3/0/3] port link-type trunk

[DeviceC-GigabitEthernet3/0/3] port trunk permit vlan 1 to 30

[DeviceC-GigabitEthernet3/0/3] quit

[DeviceC] interface gigabitEthernet3/0/4

[DeviceC-GigabitEthernet3/0/4] link-delay 0

[DeviceC-GigabitEthernet3/0/4] undo stp enable

[DeviceC-GigabitEthernet3/0/4] port link-type trunk

[DeviceC-GigabitEthernet3/0/4] port trunk permit vlan 1 to 30

[DeviceC-GigabitEthernet3/0/4] quit

# Create RRPP domain 1, configure VLAN 4092 as the primary control VLAN of RRPP domain 1,

and configure the VLANs mapped to MSTI 1 as the protected VLANs of RRPP domain 1.

[DeviceC] rrpp domain 1

[DeviceC-rrpp-domain1] control-vlan 4092

[DeviceC-rrpp-domain1] protected-vlan reference-instance 1

# Configure Device C as the transit node of primary ring 1, with GigabitEthernet 3/0/1 as the
primary port and GigabitEthernet 3/0/2 as the secondary port, and enable ring 1.

[DeviceC-rrpp-domain1] ring 1 node-mode transit primary-port gigabitEthernet3/0/1

secondary-port gigabitEthernet3/0/2 level 0

[DeviceC-rrpp-domain1] ring 1 enable

# Configure Device C as the assistant-edge node of subring 4, with GigabitEthernet 3/0/3 as the

edge port, and enable subring 4.

[DeviceC-rrpp-domain1] ring 4 node-mode assistant-edge edge-port

gigabitEthernet3/0/3

[DeviceC-rrpp-domain1] ring 4 enable

# Configure Device C as the assistant-edge node of subring 5, with GigabitEthernet 3/0/4 as the

edge port, and enable subring 5.

[DeviceC-rrpp-domain1] ring 5 node-mode assistant-edge edge-port

gigabitEthernet3/0/4

[DeviceC-rrpp-domain1] ring 5 enable

[DeviceC-rrpp-domain1] quit

# Enable RRPP.

[DeviceC] rrpp enable

Configure Device D:
# Create VLANs 1 through 30, map these VLANs to MSTI 1, and activate the MST region

configuration.

system-view

[DeviceD] vlan 1 to 30

[DeviceD] stp region-configuration

[DeviceD-mst-region] instance 1 vlan 1 to 30

[DeviceD-mst-region] active region-configuration

[DeviceD-mst-region] quit

# Set the physical state change suppression interval to 0 seconds on GigabitEthernet 3/0/1
through GigabitEthernet 3/0/4, disable the spanning tree feature, configure the four ports as

trunk ports, and assign them to VLANs 1 through 30.

[DeviceD] interface gigabitEthernet3/0/1

This manual is related to the following products:

H3C S9500E Series Switches