H3C Technologies H3C S12500 Series Switches User Manual

Page 100

# Create RRPP domain 1, configure VLAN 4092 as the primary control VLAN of RRPP domain 1,

and configure the VLANs mapped to MSTI 1 as the protected VLANs of RRPP domain 1.

[DeviceG] rrpp domain 1

[DeviceG-rrpp-domain1] control-vlan 4092

[DeviceG-rrpp-domain1] protected-vlan reference-instance 1

# Configure Device G as the master node of subring 4, with GigabitEthernet 3/0/1 as the primary
port and GigabitEthernet 3/0/2 as the secondary port, and enable subring 4.

[DeviceG-rrpp-domain1] ring 4 node-mode master primary-port gigabitEthernet3/0/1

secondary-port gigabitEthernet3/0/2 level 1

[DeviceG-rrpp-domain1] ring 4 enable

[DeviceG-rrpp-domain1] quit

# Enable RRPP.

[DeviceG] rrpp enable

Configure Device H:
# Create VLANs 1 through 30, map these VLANs to MSTI 1, and activate the MST region
configuration.

system-view

[DeviceH] vlan 1 to 30

[DeviceH] stp region-configuration

[DeviceH-mst-region] instance 1 vlan 1 to 30

[DeviceH-mst-region] active region-configuration

[DeviceH-mst-region] quit

# Set the physical state change suppression interval to 0 seconds on GigabitEthernet 3/0/1 and
GigabitEthernet 3/0/2, disable the spanning tree feature, configure the two ports as trunk ports,

and assign them to VLANs 1 through 30.

[DeviceH] interface gigabitEthernet3/0/1

[DeviceH-GigabitEthernet3/0/1] link-delay 0

[DeviceH-GigabitEthernet3/0/1] undo stp enable

[DeviceH-GigabitEthernet3/0/1] port link-type trunk

[DeviceH-GigabitEthernet3/0/1] port trunk permit vlan 1 to 30

[DeviceH-GigabitEthernet3/0/1] quit

[DeviceH] interface gigabitEthernet3/0/2

[DeviceH-GigabitEthernet3/0/2] link-delay 0

[DeviceH-GigabitEthernet3/0/2] undo stp enable

[DeviceH-GigabitEthernet3/0/2] port link-type trunk

[DeviceH-GigabitEthernet3/0/2] port trunk permit vlan 1 to 30

[DeviceH-GigabitEthernet3/0/2] quit

# Create RRPP domain 1, configure VLAN 4092 as the primary control VLAN of RRPP domain 1,

and configure the VLANs mapped to MSTI 1 as the protected VLANs of RRPP domain 1.

[DeviceH] rrpp domain 1

[DeviceH-rrpp-domain1] control-vlan 4092

[DeviceH-rrpp-domain1] protected-vlan reference-instance 1

# Configure Device H as the master node of subring 5, with GigabitEthernet 3/0/1 as the primary
port and GigabitEthernet 3/0/2 as the secondary port, and enable subring 5.

[DeviceH-rrpp-domain1] ring 5 node-mode master primary-port gigabitEthernet3/0/1

secondary-port gigabitEthernet3/0/2 level 1

[DeviceH-rrpp-domain1] ring 5 enable

This manual is related to the following products:

H3C S9500E Series Switches