H3C Technologies H3C S12500 Series Switches User Manual

Page 95

# Create RRPP domain 1, configure VLAN 4092 as the primary control VLAN of RRPP domain 1,

and configure the VLANs mapped to MSTI 1 as the protected VLANs of RRPP domain 1.

[DeviceB] rrpp domain 1

[DeviceB-rrpp-domain1] control-vlan 4092

[DeviceB-rrpp-domain1] protected-vlan reference-instance 1

# Configure Device B as the transit node of primary ring 1, with GigabitEthernet 3/0/1 as the
primary port and GigabitEthernet 3/0/2 as the secondary port, and enable ring 1.

[DeviceB-rrpp-domain1] ring 1 node-mode transit primary-port gigabitEthernet3/0/1

secondary-port gigabitEthernet3/0/2 level 0

[DeviceB-rrpp-domain1] ring 1 enable

# Configure Device B as the assistant-edge node of subring 2, with GigabitEthernet 3/0/4 as the

edge port, and enable subring 2.

[DeviceB-rrpp-domain1] ring 2 node-mode assistant-edge edge-port

gigabitEthernet3/0/4

[DeviceB-rrpp-domain1] ring 2 enable

# Configure Device B as the assistant-edge node of subring 3, with GigabitEthernet 3/0/3 as the

edge port, and enable subring 3.

[DeviceB-rrpp-domain1] ring 3 node-mode assistant-edge edge-port

gigabitEthernet3/0/3

[DeviceB-rrpp-domain1] ring 3 enable

[DeviceB-rrpp-domain1] quit

# Enable RRPP.

[DeviceB] rrpp enable

Configure Device C:
# Create VLANs 1 through 30, map these VLANs to MSTI 1, and activate the MST region

configuration.

system-view

[DeviceC] vlan 1 to 30

[DeviceC] stp region-configuration

[DeviceC-mst-region] instance 1 vlan 1 to 30

[DeviceC-mst-region] active region-configuration

[DeviceC-mst-region] quit

# Set the physical state change suppression interval to 0 seconds on GigabitEthernet 3/0/1
through GigabitEthernet 3/0/4, disable the spanning tree feature, configure the four ports as

trunk ports, and assign them to VLANs 1 through 30.

[DeviceC] interface gigabitEthernet3/0/1

[DeviceC-GigabitEthernet3/0/1] link-delay 0

[DeviceC-GigabitEthernet3/0/1] undo stp enable

[DeviceC-GigabitEthernet3/0/1] port link-type trunk

[DeviceC-GigabitEthernet3/0/1] port trunk permit vlan 1 to 30

[DeviceC-GigabitEthernet3/0/1] quit

[DeviceC] interface gigabitEthernet3/0/2

[DeviceC-GigabitEthernet3/0/2] link-delay 0

[DeviceC-GigabitEthernet3/0/2] undo stp enable

[DeviceC-GigabitEthernet3/0/2] port link-type trunk

[DeviceC-GigabitEthernet3/0/2] port trunk permit vlan 1 to 30

[DeviceC-GigabitEthernet3/0/2] quit

[DeviceC] interface gigabitEthernet3/0/3

This manual is related to the following products:

H3C S9500E Series Switches