H3C Technologies H3C S12500 Series Switches User Manual

Page 107

[DeviceC-rrpp-domain2] ring 1 node-mode transit primary-port gigabitethernet 3/0/1

secondary-port gigabitethernet 3/0/2 level 0

[DeviceC-rrpp-domain2] ring 1 enable

# Configure Device C as the edge node of subring 2 in RRPP domain 2, with GigabitEthernet

3/0/3 as the edge port, and enable subring 2.

[DeviceC-rrpp-domain2] ring 2 node-mode edge edge-port GigabitEthernet3/0/3

[DeviceC-rrpp-domain2] ring 2 enable

[DeviceC-rrpp-domain2] quit

# Enable RRPP.

[DeviceC] rrpp enable

Configure Device D:
# Create VLANs 10 and 20, map VLAN 10 to MSTI 1 and VLAN 20 to MSTI 2, and activate MST
region configuration.

system-view

[DeviceD] vlan 10

[DeviceD-vlan10] quit

[DeviceD] vlan 20

[DeviceD-vlan20] quit

[DeviceD] stp region-configuration

[DeviceD-mst-region] instance 1 vlan 10

[DeviceD-mst-region] instance 2 vlan 20

[DeviceD-mst-region] active region-configuration

[DeviceD-mst-region] quit

# Set the physical state change suppression interval to 0 seconds on GigabitEthernet 3/0/1 and

GigabitEthernet 3/0/2, disable the spanning tree feature, configure the two ports as trunk ports,

remove them from VLAN 1, and assign them to VLANs 10 and 20.

[DeviceD] interface gigabitethernet 3/0/1

[DeviceD-GigabitEthernet3/0/1] link-delay 0

[DeviceD-GigabitEthernet3/0/1] undo stp enable

[DeviceD-GigabitEthernet3/0/1] port link-type trunk

[DeviceD-GigabitEthernet3/0/1] undo port trunk permit vlan 1

[DeviceD-GigabitEthernet3/0/1] port trunk permit vlan 10 20

[DeviceD-GigabitEthernet3/0/1] quit

[DeviceD] interface gigabitethernet 3/0/2

[DeviceD-GigabitEthernet3/0/2] link-delay 0

[DeviceD-GigabitEthernet3/0/2] undo stp enable

[DeviceD-GigabitEthernet3/0/2] port link-type trunk

[DeviceD-GigabitEthernet3/0/2] undo port trunk permit vlan 1

[DeviceD-GigabitEthernet3/0/2] port trunk permit vlan 10 20

[DeviceD-GigabitEthernet3/0/2] quit

# Create RRPP domain 1, configure VLAN 100 as the primary control VLAN of RRPP domain 1,

and configure the VLAN mapped to MSTI 1 as the protected VLAN of RRPP domain 1.

[DeviceD] rrpp domain 1

[DeviceD-rrpp-domain1] control-vlan 100

[DeviceD-rrpp-domain1] protected-vlan reference-instance 1

# Configure Device D as the transit node of primary ring 1 in RRPP domain 1, with GigabitEthernet

3/0/1 as the primary port and GigabitEthernet 3/0/2 as the secondary port, and enable ring 1.

This manual is related to the following products: