H3C Technologies H3C S12500 Series Switches User Manual

Page 85

[DeviceA-GigabitEthernet3/0/2] port link-type trunk

[DeviceA-GigabitEthernet3/0/2] port trunk permit vlan 1 to 30

[DeviceA-GigabitEthernet3/0/2] quit

# Create RRPP domain 1, configure VLAN 4092 as the primary control VLAN of RRPP domain 1,
and configure the VLANs mapped to MSTI 1 as the protected VLANs of RRPP domain 1.

[DeviceA] rrpp domain 1

[DeviceA-rrpp-domain1] control-vlan 4092

[DeviceA-rrpp-domain1] protected-vlan reference-instance 1

# Configure Device A as the master node of primary ring 1, with GigabitEthernet 3/0/1 as the
primary port and GigabitEthernet 3/0/2 as the secondary port, and enable ring 1.

[DeviceA-rrpp-domain1] ring 1 node-mode master primary-port gigabitethernet 3/0/1

secondary-port gigabitethernet 3/0/2 level 0

[DeviceA-rrpp-domain1] ring 1 enable

[DeviceA-rrpp-domain1] quit

# Enable RRPP.

[DeviceA] rrpp enable

Configure Device B:
# Create VLANs 1 through 30, map these VLANs to MSTI 1, and activate the MST region
configuration.

system-view

[DeviceB] vlan 1 to 30

[DeviceB] stp region-configuration

[DeviceB-mst-region] instance 1 vlan 1 to 30

[DeviceB-mst-region] active region-configuration

[DeviceB-mst-region] quit

# Set the physical state change suppression interval to 0 seconds on GigabitEthernet 3/0/1 and

GigabitEthernet 3/0/2, disable the spanning tree feature, configure the two ports as trunk ports,
and assign them to VLANs 1 through 30.

[DeviceB] interface gigabitethernet 3/0/1

[DeviceB-GigabitEthernet3/0/1] link-delay 0

[DeviceB-GigabitEthernet3/0/1] undo stp enable

[DeviceB-GigabitEthernet3/0/1] port link-type trunk

[DeviceB-GigabitEthernet3/0/1] port trunk permit vlan 1 to 30

[DeviceB-GigabitEthernet3/0/1] quit

[DeviceB] interface gigabitethernet 3/0/2

[DeviceB-GigabitEthernet3/0/2] link-delay 0

[DeviceB-GigabitEthernet3/0/2] undo stp enable

[DeviceB-GigabitEthernet3/0/2] port link-type trunk

[DeviceB-GigabitEthernet3/0/2] port trunk permit vlan 1 to 30

[DeviceB-GigabitEthernet3/0/2] quit

# Create RRPP domain 1, configure VLAN 4092 as the primary control VLAN of RRPP domain 1,
and configure the VLANs mapped to MSTI 1 as the protected VLANs of RRPP domain 1.

[DeviceB] rrpp domain 1

[DeviceB-rrpp-domain1] control-vlan 4092

[DeviceB-rrpp-domain1] protected-vlan reference-instance 1

# Configure Device B as the transit node of primary ring 1, with GigabitEthernet 3/0/1 as the
primary port and GigabitEthernet 3/0/2 as the secondary port, and enable ring 1.

This manual is related to the following products:

H3C S9500E Series Switches