H3C Technologies H3C S12500 Series Switches User Manual

Page 103

[DeviceA-GigabitEthernet3/0/1] undo port trunk permit vlan 1

[DeviceA-GigabitEthernet3/0/1] port trunk permit vlan 10 20

[DeviceA-GigabitEthernet3/0/1] quit

[DeviceA] interface gigabitethernet 3/0/2

[DeviceA-GigabitEthernet3/0/2] link-delay 0

[DeviceA-GigabitEthernet3/0/2] undo stp enable

[DeviceA-GigabitEthernet3/0/2] port link-type trunk

[DeviceA-GigabitEthernet3/0/2] undo port trunk permit vlan 1

[DeviceA-GigabitEthernet3/0/2] port trunk permit vlan 10 20

[DeviceA-GigabitEthernet3/0/2] quit

# Create RRPP domain 1, configure VLAN 100 as the primary control VLAN of RRPP domain 1,

and configure the VLAN mapped to MSTI 1 as the protected VLAN of RRPP domain 1.

[DeviceA] rrpp domain 1

[DeviceA-rrpp-domain1] control-vlan 100

[DeviceA-rrpp-domain1] protected-vlan reference-instance 1

# Configure Device A as the master node of primary ring 1, with GigabitEthernet 3/0/1 as the

primary port and GigabitEthernet 3/0/2 as the secondary port, and enable ring 1.

[DeviceA-rrpp-domain1] ring 1 node-mode master primary-port gigabitethernet 3/0/1

secondary-port gigabitethernet 3/0/2 level 0

[DeviceA-rrpp-domain1] ring 1 enable

[DeviceA-rrpp-domain1] quit

# Create RRPP domain 2, configure VLAN 105 as the primary control VLAN of RRPP domain 2,

and configure the VLAN mapped to MSTI 2 as the protected VLAN of RRPP domain 2.

[DeviceA] rrpp domain 2

[DeviceA-rrpp-domain2] control-vlan 105

[DeviceA-rrpp-domain2] protected-vlan reference-instance 2

# Configure Device A as the master node of primary ring 1, with GigabitEthernet 3/0/2 as the
master port and GigabitEthernet 3/0/1 as the secondary port, and enable ring 1.

[DeviceA-rrpp-domain2] ring 1 node-mode master primary-port gigabitethernet 3/0/2

secondary-port gigabitethernet 3/0/1 level 0

[DeviceA-rrpp-domain2] ring 1 enable

[DeviceA-rrpp-domain2] quit

# Enable RRPP.

[DeviceA] rrpp enable

Configure Device B:
# Create VLANs 10 and 20, map VLAN 10 to MSTI 1 and VLAN 20 to MSTI 2, and activate MST
region configuration.

system-view

[DeviceB] vlan 10

[DeviceB-vlan10] quit

[DeviceB] vlan 20

[DeviceB-vlan20] quit

[DeviceB] stp region-configuration

[DeviceB-mst-region] instance 1 vlan 10

[DeviceB-mst-region] instance 2 vlan 20

[DeviceB-mst-region] active region-configuration

[DeviceB-mst-region] quit

This manual is related to the following products:

H3C S9500E Series Switches