H3C Technologies H3C S12500 Series Switches User Manual

Page 105

# Configure Device B as the assistant-edge node of subring 3 in RRPP domain 1, with

GigabitEthernet 3/0/4 as the edge port, and enable subring 3.

[DeviceB-rrpp-domain1] ring 3 node-mode assistant-edge edge-port gigabitethernet

3/0/4

[DeviceB-rrpp-domain1] ring 3 enable

[DeviceB-rrpp-domain1] quit

# Create RRPP domain 2, configure VLAN 105 as the primary control VLAN of RRPP domain 2,
and configure the VLAN mapped to MSTI 2 as the protected VLAN of RRPP domain 2.

[DeviceB] rrpp domain 2

[DeviceB-rrpp-domain2] control-vlan 105

[DeviceB-rrpp-domain2] protected-vlan reference-instance 2

# Configure Device B as the transit node of primary ring 1, with GigabitEthernet 3/0/1 as the
primary port and GigabitEthernet 3/0/2 as the secondary port, and enable ring 1.

[DeviceB-rrpp-domain2] ring 1 node-mode transit primary-port gigabitethernet 3/0/1

secondary-port gigabitethernet 3/0/2 level 0

[DeviceB-rrpp-domain2] ring 1 enable

# Configure Device B as the assistant-edge node of subring 2 in RRPP domain 2, with
GigabitEthernet 3/0/3 as the edge port, and enable subring 2.

[DeviceB-rrpp-domain2] ring 2 node-mode assistant-edge edge-port gigabitethernet

3/0/3

[DeviceB-rrpp-domain2] ring 2 enable

[DeviceB-rrpp-domain2] quit

# Enable RRPP.

[DeviceB] rrpp enable

Configure Device C:
# Create VLANs 10 and 20, map VLAN 10 to MSTI 1 and VLAN 20 to MSTI 2, and activate MST
region configuration.

system-view

[DeviceC] vlan 10

[DeviceC-vlan10] quit

[DeviceC] vlan 20

[DeviceC-vlan20] quit

[DeviceC] stp region-configuration

[DeviceC-mst-region] instance 1 vlan 10

[DeviceC-mst-region] instance 2 vlan 20

[DeviceC-mst-region] active region-configuration

[DeviceC-mst-region] quit

# Set the physical state change suppression interval to 0 seconds on GigabitEthernet 3/0/1 and

GigabitEthernet 3/0/2, disable the spanning tree feature, configure the two ports as trunk ports,
remove them from VLAN 1, and assign them to VLANs 10 and 20.

[DeviceC] interface gigabitethernet 3/0/1

[DeviceC-GigabitEthernet3/0/1] link-delay 0

[DeviceC-GigabitEthernet3/0/1] undo stp enable

[DeviceC-GigabitEthernet3/0/1] port link-type trunk

[DeviceC-GigabitEthernet3/0/1] undo port trunk permit vlan 1

[DeviceC-GigabitEthernet3/0/1] port trunk permit vlan 10 20

[DeviceC-GigabitEthernet3/0/1] quit

[DeviceC] interface gigabitethernet 3/0/2

This manual is related to the following products:

H3C S9500E Series Switches