Gasboy 1000 Series FMS Startup Manual - Manual (Page 29)

GASBOY Series 1000
5-10 03/07/03
3. Press F2 or PAGE DOWN to display the next Setup Screen, Communications Setup.
9ƒ‰‚wqiˆwƒ‚‡ÂUsˆ‰„Â
Â
Â
Iiw‚Â8i‰r !"  7‰’Â8i‰r )& Â
 Iiw‚Â@iˆiRi†wˆ“ (Pƒ‚s 7‰’Â@iˆiRi†wˆ“ (Pƒ‚sÂ
 Iiw‚ÂUˆƒ„Â8wˆ‡Â ! 7‰’ÂUˆƒ„Â8wˆ‡Â !Â
 Iiw‚ÂTqÂD‚r‡y `QP`QBB 7‰’ÂTqÂD‚r‡y PQPAÂ
 Iiw‚Â`ˆÂD‚r‡y PQPA 7‰’Â`ˆÂD‚r‡y `QP`QBBÂ
 Iiw‚ÂTqÂHss€Â % È 7‰’ÂTqÂHss€Â % ÈÂ
 Eu‚ƒ†sÂ(ˆvÂ8wˆÂ Qtt 7‰’ÂRƒ†ˆÂ TU"#"Â
 9ƒÂIƒrs B‰€€Â@‰„€s’ 7‰’ÂE‚ˆs†tiqs TU"#"Â
 @w‡qƒ‚‚sqˆÂ "ÂUsq R†w‚ˆs†Â Us†wi€Â
Â
NOTE: Series 1000 software prior to version 8.1 and FleetKey software prior to version 2.1
does not support XON/XOFF protocol. For these software versions, set the Main Rcv
Hndsk, Main Xmt Hndsk, Aux Rcv Hndsk and Aux Xmt Hndsk parameters to NONE
and set the Main Baud parameter to 1200 and Aux Baud parameter to 9600.
4.
Press F3 or PAGE DOWN to display the next Setup Screen, Display Setup.
@w‡„€i“ÂUsˆ‰„Â
Â
Â
9ƒ€‰‚‡Â !#" 8iqyu†ƒ‰‚r @i†yÂ
 ( !#"Â9€si†Â Q‚ 7ˆˆ†wp‰ˆs‡Â 9vi†Â
 Hw‚s‡Â "$ Y„†ˆÂE‚ˆs‚‡wˆ“ @wÂ
 Rius‡Â !`ÂHw‚s‡Â Y„†ˆÂTss†‡s QttÂ
 Uˆiˆ‰‡ÂHw‚s A’ˆÂ Y„†ˆÂW‚rs†€w‚s QttÂ
 9‰†‡ƒ†ÂUˆ“€s 8€w‚yÂ8€ƒqy Tst†s‡vÂTiˆs & D”Â
 9‰†‡ƒ†Â Q‚ Rƒ‰‚rÂ9vi†Â WUÂ
 Uq†ss‚ÂUis†Â !%ÂIw‚ 7‰ˆƒÂBƒ‚ˆÂHƒir Q‚Â
Â
NOTE: The
Columns setting of 132 may be changed to 80 if desired; however, this may cause
transactions displayed on the screen (and on the Okidata printer) to wrap, hindering
readability.
5.
Press F4 or PAGE DOWN to display the next Setup Screen, Keyboard Setup.
Gs“pƒi†rÂUsˆ‰„Â
Â
Â
Gs“Â9€wqy Qtt 8†siy "% ‡Â
 Gs“ÂTs„siˆÂ Q‚ `ˆÂHwwˆÂ Pƒ‚sÂ
 Gs“ÂHƒqy 9i„‡Â BGs“Â`ˆÂHwwˆÂ Pƒ‚sÂ
 Tsˆ‰†‚ÂGs“ 9T Gs“Â9ƒrs 7U9EEÂ
 A‚ˆs†ÂGs“ 9T YRÂGs“pƒi†rÂIƒrs QttÂ
 8iqyÂU„iqsÂGs“Â @AH8U HƒqyÂGs“pƒi†r @w‡ip€sÂ
 HstˆÂ7€ˆÂGs“ B‰‚qˆÂ Hi‚u‰ius WUÂ
 @s€sˆsÂGs“ Pƒ†i€Â
Â