Reznor ADFH Option - Installation - Roof Curbs Assembly - Manual (Page 13)

Form I-OPT-C, P/N 132900 R17, Page 13
Y
Z
(Return
Air
Cap)
A
B
B C
G1
G2
M
B
G2
M
N
G1
R
U
U
W
S
S
R
X
3/4” Hex Head Cap Screws with
Lockwashers and Hex Nuts (8 per corner)
2” Lag Screw and
Lockwasher (2 per corner)
Corner Hardware
for attaching “Y”:
F
(Insulation up)
3 Y’s
FIGURE 4F - Install
the Curb End with
Duct Connections
( 3 Y'S ) and the
Energy Recovery
Section Duct Top ( Z )
Counter
Flashing
(by installer;
install after
curb assembly) Insulation
2 x 4 Wood
Nailer
Cabinet
Cant Strip
(by installer) Weld, bolt,
or lag screw
curb to deck
structure.
FIGURE 4G -
Curb Detail
Dimensions (inches/mm)
FIGURE 4H - Weights and Dimensions of Options CJ54 & CJ53 for MAPS ® Unit with an Energy
Recovery Module
Supply
Duct
Supply
Duct
X
Y
Roof Curb Option CJ53 & CJ54
for MAPS with Option ER1
Energy Recovery Module
TOP VIEW
Roof Curb Option CJ53 & CJ54
for MAPS with Option ER1
Energy Recovery Module
SIDE VIEW
Return Air Duct
R
S
T
U
R
V
W
10-3/16
(259)
NOTE: Top duct liner is one piece
(illustrated) on Cabinet A. Cabinets B
and C have a two-piece top duct liner.
(MAPS Unit) (Energy Recovery Unit)
Cabinet R S T U V W X Y
A* inches 15 2-5/16 34-13/16 38-5/8 18 32 133 136-3/4
mm 381 59 884 981 457 813 3378 3473
B*
inches 22-1/2 2-5/16 49-13/16 53-5/8 18 32 133 136-3/4
mm 572 59 1265 1362 457 813 3378 3473
C* inches 28-1/4 2-5/8 61-5/16 65-1/8 22 36 167-7/8 171-5/8
mm 718 67 1557 1654 559 914 4264 4359
*See Model Size / Cabinet Size Cross Reference on
page 2.
Cabinet
Size *
A B C
Opt CJ54 Opt CJ4 Opt CJ53
lbs 675 785 1087
kg 306 356 493
Roof Curb Weight
9. Complete field installation of the roof curb
a) Check the assembly for squareness. The curb must be adjusted so that the
diagonal measurements are equal within a tolerance of ±1/8” (±3mm).
b) Level the roof curb. To ensure a good weatherproof seal between the unit curb
cap and the roof curb, the roof curb must be leveled in both directions with no
twist end to end. Shim as required and secure curb to roof deck.
c) Install field-supplied flashing (FIGURE 4G).
d) Apply 1/4" x 1-1/4" foam sealant tape to both the top surface of the curb rails
and the top surface of the perimeter of the duct dividers, being sure to make
good butt joints at all corners.
10. Lift the MAPS ® unit on to the prepared curb (See Rigging and Lifting in the unit
installation manual, Form I-MAPSIII&IV). IMPORTANT: Verify that the unit will be
placed in the correct airflow orientation to mate properly with the discharge
and return air openings. Remember that the energy recovery module is at the
discharge end of the curb.
11. After the MAPS ® unit is in place, follow the instructions shipped with the energy
recovery module (Form I-MAPSIII&IV-ER) to lift and mate the energy recovery
module to the MAPS ® unit.
12. Refer to the MAPS ® installation manual and start up information to complete the
installation.
ID P/N by Cabinet Size
Y
A-261656 B-261657 C-261672
A-261386 B-261387 C-261414
A-261388 B-261389 C-261415
Z A-262545 B-262552
&262556
C-261676
&262435
NOTE: Cabinet
Sizes B and C -
Insulated Duct Top
(Code Z) is two
piece