Brandmotion 1013-9531-V2 - Manual (Page 16)

"#$%&''&%"(#!"#$%)*+%"(#$
9530 & 9531 Instructions 1-14-13.doc Page 16 of 16
Secure Harnesses & Reinstall Vehicle Trim
96. Lift Mirror Harness and Chassis Harness connection
out of view and secure harnesses to existing wires
under the dashboard using two supplied Wire Ties.
97. Reinstall knee bolster using existing two screws and
a Phillips screwdriver.
98. Reinstall parking brake lever using the existing bolt
and a 10mm socket.
99. Reinstall end of dash cover and M-BEC electrical
cover by popping them back into place with hands.
100. Reinstall front kick panel by pressing it into place
with your hands to reengage the mounting clips.
101. Reinstall front and rear sill plates by pressing them
into place with hands to reengage mounting clips.
102. Reinstall mirror bridge wiring cover.
103.
Reinstall overhead console by pressing it back
into place to reengage the mounting clips. Then use
a T15 Torx driver to reinstall the existing screws on
each side of the console.
104. Reinstall overhead light cover by sliding the rear
tabs into their slots and popping the front of the
cover back into the console with your hands.
105. Secure supplied Mirror Harness to existing A-pillar
wiring using two supplied Wire Ties. (Figure 76)
Figure 76
106. Reinstall driver’s side A-pillar cover using existing
bolt and a 7mm socket.
107. Reinstall driver’s side A-pillar bolt cover by popping
it back into place with fingers.
108. Reconnect driver’s side sun visor wiring harness
and reinstall the sun visor using the existing screw
with a T15 Torx driver.
109. Reinstall sun visor mounting plate cover by popping
it back into place with your fingers.
110. Reinstall driver’s side sun visor anchor using the
existing screw and a T15 Torx driver. Pop sun visor
anchor bolt cover back into place with fingers.
111. Coil any excess supplied Chassis Harness and
secure to existing vehicle wiring using remaining
supplied Wire Ties.
112. Reconnect speaker wire in D-pillar and reinstall D-
pillar cover.
113. Reinstall D-pillar cover screw using a Phillips
screwdriver and reinstall D-pillar bolt cover.
114. Reinstall headliner garnish by working your way
from one end to the other and popping the
mounting pins in with your hands. Note: Make sure
liftgate weather stripping is sitting on the outside of
the D-pillar cover, D-pillar trim, and headliner
garnish.
115. Reinstall liftgate sill plate by setting it into place
and pressing down to re-engage mounting clips.
116. Reinstall liftgate button connector to the upper
liftgate trim panel.
117. Reinstall lower liftgate trim by aligning it with the
liftgate. Working your way from one end to the
other, pop the mounting pins in with your hands.
118. Reinstall upper liftgate trim by aligning it with the
liftgate and working your way from one end to the
other, popping the mounting pins in with your
hands.
119. Reinstall pushpins from the rear window latch trim
by pressing them into holes with your fingers.
120. Reinstall liftgate pull strap using existing hardware
and a T30 Torx driver.
121. Reinstall grab cup on the bottom of liftgate using
existing hardware and a T30 Torx driver.
122. Reinstall third row seat.
Camera, Chassis, and Mirror Harness
Pinouts
(reference only)
PIN
# FUNCTION
CAMERA
HARNESS
COLOR CHASSIS
HARNESS
COLOR MIRROR
HARNESS
COLOR
1 Video (+) White White Gray/Dark Blue
2 Shield Blue Blue White
3 Reverse Green Green Green
4 Video (-) Brown Brown Gray/Orange
5 Ground Black Black Black
6 Ignition Red Red Pink