Brandmotion 9002-9504-V1 - Manual

Installation Instruction Overview - Rear Vision System Mirror Display
2007-2013 Chevy Silverado and GMC Sierra
(Kit Part numbers 9002-9503 without Compass/Temp and 9002-9504 with Compass/Temp
9503 & 9504 Instruction Overview 7-11-13.doc Page 1 of 2
REQUIRED CONNECTIONS
Kit #
Wire
Color
Polarity Function Connection
Instruction
Steps
9002-
9503
Gray/
Blue + Video Signal Rear View Mirror Connector cavity 6 53 – 58
Gray/
Orange - Video Signal Rear View Mirror Connector cavity 7 53 – 58
9002-
9504
Gray/
Blue + Video Signal Rear View Mirror Connector cavity 1 53 – 58
Gray/
Orange - Video Signal Rear View Mirror Connector cavity 2 53 – 58
9002-
9503
&
9002-
9504
Pink + Ignition
M-BEC C12 Brown Connector cavity 7 60 – 62
Alternate connection: BCM X5 Brown Connector cavity 13 68
Green + Reverse
M-BEC C11 Light Gray Connector cavity 5 OR
M-BEC C10 Gray Connector cavity 8
63 – 67
Alternate connection: BCM X5 Brown Connector cavity 11 68
Black - Ground Lower knee bolster stud 69
• Verify kit contents are complete. See complete instructions enclosed. For the latest full color instructions, as well as an
installation video, please visit www.brandmotion.com
• If installing a 9002-9504 kit on a 2009 and up vehicle, purchasing a 9002-6008 kit (temperature harness) is required. Refer to
Kit 9002-9511 instructions posted on www.brandmotion.com for complete installation procedure.
• Vehicles without an auto dimming mirror require purchasing a 9002-6105 kit (mirror harness). See Step 57 for install details.
Preparation (Steps 1 thru 4 in supplied complete kit instructions)
1-3 Turn lamps, accessories and ignition off. Disconnect negative battery cable.
4 Wait one (1) minute to assure the SIR roof rail air bag system is disabled before proceeding.
Install Camera Bezel into Tailgate (Steps 5 thru 29 in supplied complete kit instructions)
5-10 Lower tailgate to remove tailgate bezel and then remove tailgate and place on work surface.
11-17 Using the supplied Template, drill 29mm (1-1/8”) hole(s) for camera grommets at the bottom of the tailgate and pickup box.
If the pickup box already has an existing hole, remove its flange so the grommet will fit. Clean rough edges of drilled hole(s)
using a deburring tool and then apply supplied anti corrosion coating.
18-20 Prepare the supplied Camera Bezel by transferring the vehicle’s lock cylinder or installing supplied Lock Plug.
21-24 Route the camera harness through drilled hole in tailgate. Snap Camera bezel in place and seat grommet.
25-29 Remove rear license plate, if present. Reinstall tailgate, route the camera harness through the drilled pickup box hole and then
seat the grommet into pickup box hole.
Determine Reverse Signal Location (Steps 30 thru 33 in supplied complete kit instructions)
30-31 Remove left instrument panel outer trim cover and M-BEC cover.
32
Have an assistant set parking brake, start vehicle, and shift into Reverse. Using a digital multimeter, check for reverse signal in
Cavity 5 at the Light Gray C11/X11 Connector OR Cavity 8 of Gray C10/ X10 Connector in the M-BEC.
33
If reverse signal is NOT present in the C10/ X10 Connector or C11/ X11 Connector:
A. Check that bail that secures the M-BEC connectors is fully locked. Repeat Step 33.
B. If reverse signal is still not present, check Fuse Block for any blown fuses. Replace fuses and repeat Step 33.
C. If reverse signal is still NOT present, connection to reverse signal must be made at the BCM rather than C10/ X10 or C11/
X11 Connector (refer to Step 67 under “Connect Mirror Harness to Power, Reverse, and Ground”).
Cut Accessory Pass Through In Front of Dash (Steps 34 thru 39 in supplied complete kit instructions)
34 Remove Parking Brake Release Handle Bolt and remove Handle. Remove two Knee Bolster screws, remove Knee Bolster, and
Disengage M-BEC from support bracket.
35-37 Move M-BEC up into instrument panel to access front of dash matte opening to locate drilling location. Drill a 25.4mm (1”)
hole for grommet near existing dimple or existing grommet.
38-39 Clean rough edges of drilled hole(s) using a deburring tool, and apply supplied anti corrosion coating.
Install Mirror and Route Interior Harness (Steps 40 thru 51 in supplied complete kit instructions)
40 Unplug vehicle’s Inside Rearview Mirror (ISRVM) connector.
41-45 Tilt mirror upward and loosen screw with a T20 Torx driver. Gently slide mirror upward to remove. Remove mirror wire cover.
46-51 Remove driver’s side A-pillar trim, driver’s side sunshade, and overhead console assembly.