Yamato Scientific SQ 510 Autoclave, Sterilizers - Manual (Page 38)

35
Operation Method
Memory Function
Memory function
Each operation course has three memory banks, where registration and read of settings are possible.
The following settings can be stored into the memory.
・
Sterilization (melting) temperature
・ Sterilization (melting) time
・ Heat-retention temperature
・ Heat-retention time
・ ON/OFF of forced cooling function
1. Register the setting to the memory.
MANUAL MELT
PRE HEAT
AUTO
TEMP
PRES.
STERILIZE/MELT
HEAT
EXHAUST
WARM
SAMPLE
STERILIZE
WARM /LIQUID
COOLING
FAN
WARM
℃
END
TIME
MAINT.
ENTER ENTER WARM STERILIZER
/MELT
STERILIZER
/MELT
START
WARM
STERILIZE
/NORMAL
STERILIZE SET
MEMORY
START/
STOP
① Make sure that the course where the memory is to be
registered is selected and then press the SET MEMORY key.
The SET MEMORY lamp blinks.
MANUAL MELT
PRE HEAT
AUTO
TEMP
SAMPLE
STERILIZE
WARM /LIQUID
COOLING
FAN
WARM
℃
TIME
MAINT.
ENTER ENTER
WARM STERILIZER
/MELT STERILIZER /MELT
START
WARM
STERILIZE
/NORMAL
STERILIZE SET
MEMORY
START/
STOP
② The memory registration screen is displayed.
The memory No. is displayed on the highest-order digit of
temperature display screen. The temperature/time setting
display for sterilization or melting switches to 1, 2, 3 or normal
mode in this order every time the SET MEMORY key is
pressed.
As for the courses that include the heat-retention setting, the
temperature and time of the setting can be checked by
pressing the ENTER key.
The COOLING FAN lamp lights up when forced cooling
function is set to "on".
MANUAL MELT
PRE HEAT
AUTO
TEMP
SAMPLE
STERILIZE
WARM /LIQUID
COOLING
FAN
WARM
℃
TIME
MAINT.
ENTER ENTER
WARM STERILIZER
/MELT STERILIZER
/MELT
START
WARM
STERILIZE
/NORMAL
STERILIZE SET
MEMORY
START/
STOP
MANUAL MELT
PRE HEAT
AUTO
TEMP
SAMPLE
STERILIZE
WARM /LIQUID
COOLING
FAN
WARM
℃
TIME
MAINT.
ENTER ENTER
WARM STERILIZER
/MELT STERILIZER /MELT
START
WARM
STERILIZE
/NORMAL
STERILIZE SET
MEMORY
START/
STOP
③ Select the memory No. that the setting is overwritten and then
press the SET MEMORY key for two seconds. The displayed
preset value changes. This completes the registration of
setting.
2. Operation procedures with the registered setting
MANUAL MELT
PRE HEAT
AUTO
TEMP
PRES.
STERILIZE/MELT
HEAT
EXHAUST
WARM
SAMPLE
STERILIZE
WARM /LIQUID
COOLING
FAN
WARM
℃
END
TIME
MAINT.
ENTER ENTER
WARM STERILIZER /MELT STERILIZER /MELT
START
WARM
STERILIZE
/NORMAL
STERILIZE SET
MEMORY
START/ STOP
① Make sure that the course to be operated is selected and then
press the SET MEMORY key. The SET MEMORY lamp blinks.
MANUAL MELT
PRE HEAT
AUTO
TEMP
SAMPLE
STERILIZE
WARM /LIQUID
COOLING
FAN
WARM
℃
TIME
MAINT.
ENTER ENTER
WARM STERILIZER
/MELT STERILIZER /MELT
START
WARM
STERILIZE
/NORMAL
STERILIZE SET
MEMORY
START/
STOP
② The memory confirmation screen registered is displayed.
Select the memory No. by the SET MEMORY key.
③ Press the START/STOP key. The setting being displayed is
read. The equipment starts operation using the setting.
②
③
2sec.