Yamato Scientific SQ 510 Autoclave, Sterilizers - Manual (Page 32)

29
Operation Method
Sterilization & Warm/Melting & Warm/Manual Course
Follow the procedures below for the setting of sterilization & warm, melting & warm and manual course.
1. Turn on the earth leakage breaker
• The temperature display screen and time display screen
display the current temperature inside the chamber and
current time (standby state) respectively when the breaker is
turned to on.
℃
ENTER ENTER
TEMP
WARM
TIME
WARM STERILIZER
/MELT
STERILIZER
/MELT
MANUAL MELT
PRE HEAT
AUTO
TEMP
PRES.
STERILIZE/MELT
HEAT
EXHAUST
WARM
SAMPLE
STERILIZE
WARM /LIQUID
COOLING
FAN
WARM
℃
END
TIME
MAINT.
ENTER ENTER
WARM STERILIZER
/MELT STERILIZER
/MELT
START
WARM
STERILIZE
/NORMAL
STERILIZE SET
MEMORY
START/
STOP
2. Select the operation course
• Press either the STERILIZE→WARM or MELT→WARM or
MANUAL key once.
Press the key twice if other course has been already selected.
MANUAL MELT
PRE HEAT
AUTO
TEMP
PRES.
STERILIZE/MELT
HEAT
EXHAUST
WARM
SAMPLE
STERILIZE
WARM /LIQUID
COOLING
FAN
WARM
℃
END
TIME
MAINT.
ENTER ENTER WARM STERILIZER
/MELT STERILIZER
/MELT
START
WARM
STERILIZE
/NORMAL
STERILIZE SET
MEMORY
START/
STOP
3. Set the sterilization temperature
① The sterilization temperature currently set is displayed with
blinking on the temperature display screen. The
STERILIZER/MELT lamp blinks. Press the ∧ ∨ on the
TEMP key and set the desired sterilization temperature.
② After setting the temperature, press the ENTER key to
determine the value.
MANUAL MELT
PRE HEAT
AUTO
TEMP
PRES.
STERILIZE/MELT
HEAT
EXHAUST
WARM
SAMPLE
STERILIZE
WARM /LIQUID
COOLING
FAN
WARM
℃
END
TIME
MAINT.
ENTER ENTER WARM STERILIZER
/MELT STERILIZER
/MELT
START
WARM
STERILIZE
/NORMAL
STERILIZE SET
MEMORY
START/ STOP
4. Set the sterilization time
① The sterilization time currently set is displayed with blinking
on the time display screen. The STERILIZER/MELT lamp
blinks. Press the ∧∨ on the TIME key and set the desired
sterilization time.
② After setting the time, press the ENTER key to determine the
value.
MANUAL MELT
PRE HEAT
AUTO
TEMP
PRES.
STERILIZE/MELT
HEAT
EXHAUST
WARM
SAMPLE
STERILIZE
WARM /LIQUID
COOLING
FAN
WARM
℃
END
TIME
MAINT.
ENTER ENTER
WARM STERILIZER
/MELT STERILIZER
/MELT
START
WARM
STERILIZE
/NORMAL
STERILIZE SET
MEMORY
START/ STOP
5. Set the heat-retention temperature
① The current heat-retention temperature is displayed with
blinking on the temperature display screen. The
STERILIZER/MELT lamp blinks. Press the ∧ ∨ on the
TEMP key and set the desired heat-retention temperature.
② After setting the temperature, press the ENTER key to
determine the value. The setting of heat-retention time will
follow.
Temperature display screen:
displays current temperature inside the chamber.
Time display screen:
displays current time.
① ②
① ②
① ②